I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi,
I am working on the nrf5340 with zephyr (NCS 1.7.1), I need to monitor the voltage of the battery, in the beginning, I used the ADC API of zephyr, and it works well...
Currently I have a 52840 peripheral running peer manager. We bond/peer with it using a passkey system from an mobile phone central. It works great.
SDK is 1702 nrf5.
What...
I wanted to confirm that on the nRF9160, it is acceptable to tie the VDD and VDD_GPIO pins to the same 3.3V rail and bring them up together. The VDD_GPIO rail will not be...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard
I want to add UART implementation....
Hi everyone!!! I need help with our new version of HW after validating the previous one that works.
I read some similar posts related to the GPRETREG for HOLD a GPIO while...
Hi Nordic,
We have a design where we'd like to share the 2.4 GHz antenna between WiFi and BLE.
Therefore, we need to power and configure the RF switch accordingly, before...
Hi,
currently I am using nRF52811 in one product with BLE functionality. Now I would like to use the same MCU in other product where BLE is not needed. In this case I would...
We are developing a product based on nRF52832 and we need to verify that in case of problems, the device will "fail gracefully". So we looked at implementing the ARM handlers...
I am using LSM6DSOX IMU sensor INT detection with NRF52-DK and have extra 400µA (PPK2 used) on my setup. After a few days of nightmares I finally found that this is related...
Hi,
I'm using nRF Connect SDK v1.9.0
We're working on firmware running on an nRF9160 with TF-M enabled. We need to link with a library to is built with hard-float, so...
Hi,
i want to read temperature sensor value inside the nrf soc on bl653 board. while checking there is a file inside ( \zephyr\drivers\sensor\nrf5) this path. how to configure...
Hi,
I am working on DFU-OTA example. am looking for example , which will help me to copy image from slot1 to slot0 without using scratch pad. it has to override the image...
Hello Team,
I am using the ble_app_hrs_rscs_relay example where NRF52 acts both as a central and peripheral. My question is that when I remove the heart sensor Polar H10...
Hi,
I am working on DFU-OTA sample as suggested in this link. https://devzone.nordicsemi.com/f/nordic-q-a/84766/sample-ncs-code-to-evaluate-dfu-ota-on-nrf52833 .
For nrf52833...
Hello,
I'm using a custom board and i actually have a problem that I never saw before : error 34 (0x22) GATT CONN LMP TIMEOUT.
I have send frames : I did my own custom...
