Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello,
I'm trying to implement a sleep mode for my application. Currently it has around 8 tasks.
I need to disable them all + disable some HW, such as GPS module. And...
Hello Nordic Team!
I'm working with the ble_app_hrs_c and a UART code I developed following the peripheral/uart example.
On the peripheral/uart example we have the following...
Hi,
I am using nordic52840 development kit board. and I am using sdk17.1 for development.
I tried to create .bin for secure bootloader code inside DFU. but the file...
hihih
I have DK9160 and THINGY91, which I bought 2 years ago.
I want to use them now.
I got the output:
***** Booting Zephyr OS build v1.14.99-ncs2-495-ga8933a2ead01...
Hi, I am using NRF9160 than I am using mqtt_simple example. I modified it. I want to send 4200 byte to mqtt broker but I get error. error is:<err> mqtt_simple: Publish failed...
Hello!
I have been working through examples lately trying to get the GPIO and PWM to work. But one issue I keep coming up to is how to define pins as input or output, and...
We have recently had a problem with the last programmer release (2.3.1). If we use an old version (2.2.0) we can plug our j-link edu and program our PCBs, if we use the last...
Hi,
We have a piece of code based on zephyr Driver to set up a double-edge GPIO interrupt. I set the interrupt flag to GPIO_INT_EDGE_BOTH. But it doesn't seem to trigger...
Hi,
I am using nrf52840 development kit with SDK 17.1.0.
I created a new project in IAR 8.50 and replicate project for sceure_bootloader in new project by adding files...
Hi!
We observe that our nRF91 SLM's get "softbricked" at random times, and a lot of them at the same time (We feel this is because of network unstability). These get stuck...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Please tell me about the value of "ble_gap_evt_t::conn_handle".
I use central and peripheral. I have the following...
Dear nordic experts, when app_error_fault_handler() gets called, the firmware application hangs in an endless loop. While this is useful during development, it's a nightmare...
Hi everyone again,
We have a custom board using nrf52840. We upload a bootloader with J-Link. https://github.com/adafruit/Adafruit_nR ... 40_express But we have a problem...
I am working on a project, using nrf52840 as a BLE Center to connect to BLE HID devices, but every time the connection is automatically disconnected when the service is discovered...
