Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello Everyone,
I am a beginner for working on Nordic devices. I have one query. I have to build a firmware in NRF52840. Now 2 different apps will be connecting to this...
Hello
I am using 5 nrf52833 dev kits and the ble_zigbee_dynamic_light_bulb_eddystone example from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I have modified the following...
I'm trying to achieve a low power operation on a device which has a nRF52833 module with a SPI peripheral on Zephyr. It is based on the peripheral_lbs.
The intended behaviour...
Hi, I am learning how to implement Long Range on the UART central and peripheral examples using SDK 17.0.0. The error I am facing is that the debug terminal shows
[ app_timer...
The provided ble_app_template10056e from nRF5_SDK_17.1.0_ddde560 crashes:
The crash was reproduced using:
1. nRF52 DK Kit - ( https://www.nordicsemi.com/eng/Products...
Hello,
Can anyone know how to print MCUboot info on serial debug terminal or Normal Debug terminal using COM port?
What are the Configurations to be added for this?...
Hi guys
I am working on a project need to pass the ADS1231 read data through BLE. But I haven't done so far. I just try to read the ADS1231 value first. Referring to some...
I see an example of a central device and peripherals as one, and I see it using the following three registers to determine the start or end of the broadcast, the beginning...
As stated in the title.
I am using nrf52832 provisioner example with light_lightness example in v4.2.0. Provisioner is able to set up the network with clients and servers...
Hi support team,
We have a new project now. We plan to use nrf52832 for the project. We know about the BLE and the related development, but we are not familiar with nordic...
I am using C++ to program the nRF52 DK and I am trying to use the standard vector library.
When I try and compile it I get the linker error:
${GCC_PATH}/arm-none-eabi...
Hi I am trying to do the led blinking in nrf52840 but the led is not even turning on i have given the code below can any body help me out.
nrf_gpio_cfg_output(14); nrf_gpio_cfg_output...
Hello,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
I recently purchased a Thingy 52 with the goal of processing the the raw magnetometer, accelerometer and gyroscope data using a sensor fusion algorithm to determine orientation...
