Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi all,
we are trying to connect 20 peripherals to one nRF52840 master (connected to a Laptop running a python app with pc-ble-driver-py) and transmit about 1000 Bytes per...
Hi guys,
I have a custom board containing a Raytac nRf52840 module running the Arduino core. The Arduino core configures the nRf52 to expect a 32K crystal on the xtal input...
Hello
I Just got my first Custom PCB's i dont know how to compile the code into them .Can someone help me . I just get the errror messege when i try to find target :
Failed...
Hello, I am using SDK 16.0 and mesh SDK 4.2.
We successfully implemented remote provisioning capabilities in our devices' firmware. One thing we are noticing though is that...
Hi,
I am using spis example from "SDK v17.0.2" with slight modification in the code as given below
On the Master end CS pin is pulled low and send 1 byte(0x45) only...
Hello,
I'm using nrf52840 with gcc compiler and SDK15.3. For our firmware update procedure, we use two flash storage instances. One for the transmitted new application and...
Nordic：
We need to do a communication certification, we need NORDIC to provide S112V6.1.1 QDID: 125078 certification report certificate。
thinks
jermi.jin
2021.061...
My CMD.EXE is copied here, it shows the command I'm trying to run, and the output of the program. As you can see, there is no error message.
However, it does not succeed...
Hi there,
I was wondering, do you have a generic "module on PCB" for Nrf9160? Much like ESP32. I would like to skip the design of the RF impedance maching... not my cup...
Hi,
I needed assistance to get the SKY66112-11 FEM working with the Radio Test Example, for certification testing (FCC, CE etc). I am using the NCS 1.5.1 SDK. I have followed...
Howdy ya'll,
I updated nRF Programmer yesterday (1.4.8 -> 1.4.9) and noticed binaries were not flashing to my board anymore. My JLINK is able to read the device's memory...
Hi, I am in need of some guidance. The overall goal is to set up MQTT/TLS communication from end devices in a thread network, via a border router to the AWS cloud. I have...
Hi. I am currently having a nrf52840 custom board and tried to program the sniffer hex file. nRF programmer gave me couldNotOpenDevice (0x4) Lowlevel error: JLINKARM_DLL_ERROR...
Hi all, I have a problem. I'm using a mix of the nrf samples azure_fota and azure_iot_hub connecting to Azure, using certificates X.509. The problem is the expiration date...
