Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi,
What I would like to do:
I'm attempting to compile pc-ble-driver connectivity firmware with S132 v5.0.0. Following the instructions on the pc-ble-driver repo on Github...
Hi All,
I am using nRF52833 to make a Thread end device, and encountered a problem with the Thread network configuration in NCS. I want the device to connect to the Thread...
Dear Nordic expert,
I'm using nRF52840 as central with SDK 16.0.0.
I establish a connection with a peripheral (phone) and then I need to drop the connection. I set a timer...
Hi, everyone on the community
When using the BLE_APP_UART example, the serial port sends a packet of data to the mobile phone every 10ms, resulting in the device disconnecting...
I want to have a very stripped down version of the cat-tracker-app that just deals with settings, so I can import what is useful to an existing web application. I am new to...
I have succesfully got extended advertising working using the nRF SDK on the nRF52 DK, however I haven't been able to assign it a 128 bit service guid.
Setup:
The device...
Hi,
I want to add DFU to our board running SDK11 S130 but facing some problems.
I followed the instructions on infocenter, and started with ble_app_hrs example (from here...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
Hi All, I try to run the example GFX in sdk 17.02.
I wired the TFT :
---VCC ------------------ +3V ---GND ------------------ GND ---CS -------------------- P1.09 --...
Hello ,
NRF52840
sdk 15.2
In my application using ble central example in nrf52840 , i am able to write data in led characteristics and getting notification on HVX using...
Hi, I have tried to add support for BOS descriptor by appending a custom class generated from the Dummy example. The "main" class is the HID generic class, but with the NRF...
Hello
I only used PWM_library, but this is my first time using PWM_driver. Simply controlling the duty cycle of multiple channels has been successful, but I am not sure...
A little backgroud for my project. The goal of the project is to be able to identify the proximity of beaconing devices in an area to a specific observer which then reports...
Hi, Below is the mapping of RAM on the 840 from the infocenter. We want to utilize the functionality to turn off unused RAM (via sd_power_ram_power_clr), but we see that if...
I am using SoftDevice s140v6.1.1. The behavior is I was able to program nRF52840 through JTAG without any issue. I am checking out the OTA firmware update feature and nRFConnect...
