Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi, all
I am studying the bsp part while looking at the example of 'ble_app_uart'. (pca10056)
The difference between 'bsp_event_handler' and 'bsp_button_event_handler...
Hi DevZone,
I want to perform USB bulk transmits to a host device while using the app_usbd library. I am using SDK 15.3 and the s140 soft device is enabled.
I have found...
Hello Nordic Team;
The Vdd value range for the nRF9160 is 3.00 V to 5.5 V. We will use li-PO battery in our system. Can I power the nRF9160 directly from the battery without...
Hi,
I am using Nordic thingy 52 for my application, Now I need to blink LED for 5 seconds on Board when ever a condition is satisfied. But in schematic of Nordic thingy...
Board: nRF51-DK (nRF51422 chip)
SDK: 12.3.0
SoftDevice: S130
Compilation settings
Optimization level O1
Debug information generated
I have seen lot of...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0....
Platform: nRF5340-DK
Tools: I am using SDK 1.5.0 (but seen on earlier SDKs too)
Configuration: Using high speed spi pins whether for SPI1 or SPI4
If I use SPI1 I see...
Hey guys i wanted to ask you for help on IOS BLE i am currently seeing that nRF Connect seems to work fine over BLE Connection with some devices on Android and as far as i...
Hi,
I'm using NRF52840 in order to connect to a mobile app via BLE.
When connection to IOS, I have an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
This event handle...
Hi,
Greetings!
We are exploring nRF9160 SIP DK and Thingy91.
Here we have understood that it has GPA and LTE-M.
We wish to use it for India region in moving objects...
We are using the advanced UARTE library to get advantage of EasyDMA to receive data from a LTE module.
We also implemented hardware flow control. THe problem is that the...
Hi fellow devs:) I'd really appreciate some advice on this please. I've come to a bit of a dead-end. Hopefully you can spot a mistake I've made. I am trying to produce a low...
Hi,
-I have a custom board using nrf 52832 and I have interfaced sensor using an SPI interface. -I am using SDK 15.2.0 and SPI driver. -I am collecting raw data and send...
