We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
HI,
I'm using the zigbee CLI example as coordinator and have another CLI device for reference as router. With my sniffer I can log the association sequence with the cli...
Hello,
I have a nrf5340 PDK .
The kit does not work right, because i got a several errors.
For example in nrf connect v.3.6.1 the PDK is shown as 000000123456 also in...
Hello Nordic support,
I would like to confirm whether nrf52840 supports only Bluetooth 5.0 features or does it also support Bluetooth 5.2 features. If it supports Bluetooth...
Hello, I am working on Nrf52 mesh network and need to update device via any host mcu or flash connected with the nrf52. But could not find any way to implement it.
If anyone...
I have changed our code that has been running on v1.4 successfully to v1.5
Mainly because I'm hoping for an improvement in the reliability of the new modem library.
However...
Hi All
Can anyone please point me to any documentation/app note that explains how the UE receives a Valid paging message when Network wants to reach the UE. Is there a...
Hallo,
IDE: Segger Embedded Studio
nrf52840 DK
Custom Board with ProteusIII
I have designed a custom board with ProteusIII (nrf52840 SoC) and was working with...
Hi,
I am currently in India city Bengaluru.
as ibasis sim does not support my region so
i am trying to connect nrf9160 to lte network using airtel sim card, but it is...
Hi,
We are working on a new product with " nRF52832 " IC. We want to test our design RF antenna (PCB trace Antenna) performance. For RF test we found an example code and...
If I change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE in sdk_config.h to any value greater than 23, immediately after connecting the stack executes a sd_ble_gattc_exchange_mtu_request...
Hi, I found that hci_usb sample may not work correctly with nrf5340pdk from the following q&a. It means that nrf5340dk support hci_usb sample?
https://devzone.nordicsemi...
Hi:
I'm using "nRF5_SDK_17.0.2_d674dde"
A question about the macro NRF_LOG_INFO.
the statement in the source code NRF_LOG_INFO("Disconnected connection handle");
...
Hi, all
I just asked similar one yesterday, but I think this should be resolved first.
I want to merge ble_app_uart_c and ble_app_uart.
So I added scan_init / scan_start...
Hi Nordic,
I am trying to make the read and write to the MX25R6435 with QSPI interface, any examples to this? I am using the sdk 17.0.2
Thank you in advance
Hi,
I was wondering what example to use if I have an accelerometer on a breadboard connected to the nRF52840 DK via TWI/SPI and the DK connected via USB to my Mac? I want...
