Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I have successfully implemented DFU over the Air function using Android-DFU-Library (Github) for my Android mobile phone.
The Android-DFU-Library needs Android 4.3+ at least...
Hi, I am after a bit of advice regarding the SPI interface between a nRF52832 acting as a master, and 3 slave devices. I only need to communicate with one SPI device at a...
Hello,
my goal is to measure the average current consumption of an external chip connected to the Power Profiler Kit on Windows 7. Since the Software inside the nRF Connect...
using SDK 12.1.0
The original error (compile time only) is
main.c(338): error: #94-D: the size of an array must be greater than zero
my snippet @ line 338:
SOFTDEVICE_HANDLER_INIT...
We run SR3 on android system which is working , need change system to embeded linux .
we run SR3 on embeded linux , i can't use voice function .
we get son info: https...
I wanted to use the sdk board support file with coustom board having 13 buttons. I have modified the bsp.c and configer number of low power events and added a coustom header...
Hi,
i have interfaced a ADC device in the nrf2 development kit,i am getting the values from the adc after using the SAADC example,
i want to implement the same with the...
Hi softdevice uses s130 The board is using nrf51 dk. The example uses the ble_app_beacon example from sdk12.3. if (switch_hit ()) { // NRF_POWER-> SYSTEMOFF = 1; // sd_power_system_off...
Hi Team,
Being trying to run the Thingy 52 mesh demo following : https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
I am using pre-built .hex file Thingy_node_s132...
Hi there,
Recently I bought an LTE module which uses a nRF52840 as the main processor to control the modem, I want to erase the flash for that module and flash the project...
Hello,
Recently I added TWI to my project it keeps a low consumption before call TWI functions to read or write after this my current consumption increases and keeps above...
I'm using the nRF BLE Mesh SDK 2.2.0 with SES v3.5 (64bit for Windows)
Our hardware with nRF52832 using internal RC
I'm running the light_switch_proxy_server but with...
Hello,
I'm just starting to use the nRF Smart Beacon kit.
Is it possible to have the beacon toggle a GPIO on-board when the beacon is out of range of the phone/app?
...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I want to ask how to use app timer with scheduler.
Here is my implementation. I just use APP_TIMER_APPSH_INIT...
