Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
We've developed a custom board with buttons(peripheral) which will talk to another custom board operating as a repeater (central on one side to talk to our custom board...
Hi,
What are the possibilities for flashing a new nRF52840 device on a custom board. Do I need the jtag interface or does the device comes preloaded with some wireless bootloader...
Hello everyone,
I have interfaced an encoder and speed sensor on a spinning bike that all connect to arduino via COM/USB port. The COM port communicates to a game engine...
Hi, I am using nRF52840 kit and using Ubuntu Host PC. I am running usbd_cdc_acm_example with below link :
https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15...
At nRF cloud introduction pag, I got the impression the "nrf cloud" front end source code is/or will be available in open source.
Am I correct? The nRF cloud source is...
I am using nfc_t4t_lib and I need to send a response 100ms after I receive the NFC_T4T_EVENT_DATA_IND event. How do I extend the response timeout by sending S(WTX)? There...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I am testing my I2C function by using ".examples\peripheral\twi_sensor" of SDK 15.2.
Because my SDA and SCL is define in P0.04 and P0.02, and my I2C Slave is MPU6050...
Hello,
I would like to know that what are the provisioning parameters needed to add an Unprovisioned device into a mesh network?
Thanks and regards,
Jahnvi.
We, I am using nRF 5 SDK v 14.2.0.
This time, without using WDT, using only the application timer, We are developing a process to send data by detecting acceleration and...
Hi,
I'm currently trying to implement Peer Manager in my existing project, for both pairing and bonding. I'm using the ble_app_template in examples/ble_peripheral in the...
Is it possible to use the TWIM and TWIS at the same time with 2 different I2C buses with openthread.
I tried this with THREAD SDK 1.1 and had link problems because of the...
Hi, I'm trying to setup attribute reporting on zigbee HA, the device role is ZB_ZCL_CLUSTER_SERVER_ROLE, I want to configure reporting for cluster 0x0006, so each time I flip...
SDK v14.0, SD132 v5.0.0
We're creating and starting app_timer instances before we enable SoftDevice via nrf_sdh_enable_request(). It seems to work, but I remember that...
