Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hello Nordic, we use the nrf52 proprietary protocol in the project, it will send 200 data per second, and no ack confirmation, the application data length is 25 or 32 bytes...
SDK 15.2
Segger Embedded Studio Release 4.12 with DEBUG on
Segger Ozone V2.60k
FreeRTOS 10 from SDK (same issue with FreeRTOS 10.1.0 source files and original ported...
What is the exact sequence when reading a characteristic with variable length and authorize required.
When I have a actual data length of 14 I can read with offset = 0 and...
Hi All Team Members,
Using Nordic Development Kit of nrf52832 I am able to write and test basic application using UART and BLE
using this kit I get the following error...
Hello, I use a custom board with nRF51822QFAA, with two buttons (left, right) and uart for printf/debug. The idea of the project is to have the board always sleeping, it wakes...
Hi,
I have a project which need to use two UART interface at the same time.
As well known, there only have one hardware UART interface in nRF51822/nRF52832. If I want...
Hello, DevZone,
I have programmed an nRF52-DK with the unmodified SDK's ble_app_hrs_pca10040_s132 (heart rate monitor) BLE peripheral application. I also have a Power Profiling...
Hi Susheel,
Thank you for your support.
We would like to get your advice related our new design, with the followings:
Assume we need to support besides of the BT5...
Hi,
I am developing one of the my project on custom board, in which I have to configured the two GPIO Pin's as input to sense the those pin and take actions assigned on...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
Hello,
I am new in this platform. Few days ago, my boss give me a nRFgo Motherboard. He want me to write a program that nRF24le1e can read/write data from sensor via I2C...
