I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Say I have 3 records, then I delete them and collect the garbage. If I try to save a new record again, it will be saved with a record ID 4 , but it should be back to 1 after...
I want to use the development kit for Bluetooth 5.0 IoT product development.
Is there already a bluetooth mesh software available for the nRF52840 development kit?
Or...
I am working on time synchronizations between different nodes in a mesh network. I have earlier worked on the radio and the ppi examples given. I wish to generate time stamps...
Hi
I would like to prepare a provisioning hex file for my firmware.
Can somebody supply an example how this could be made?
I'm using gcc toolchain, Eclipse and SDK...
Hello,
I am using sdk12.2.0 and pca10028 dk. I am using one code downloaded from unknown source. The code is used to store data in flash. When I compile through keil I don...
Hi,
i try to establish a communication between 3 sensors in the following way!
Node 1 should broadcast messages to Node 2 and Node 3 as Peripheral.
To establish a...
Hello,
I am using pca10028 and sdk 12.2. I have interfaced temp sensor with nrf51 and now I want to store that data continuously in memory of nrf51. I want to store min 4k...
Hello, I want to program and debug the nrf52840 device but I'm kind of stuck at the programing range/address issue.
I'm using my customized board so I doubt Nordic Semi...
First I register the address of the central device to the peripheral device. When I work with a single peripheral device and a single central device, I can send commands from...
I'm trying to understand the subtleties in a Gazell link setup with multiple devices and a single host.
The documentation in the infocentre suggests minimum timeslot_period...
Hi,
Just wanted to confirm what the average current measured by the PPK represents. So for example if I have AVG in average window as 2.5mA, is that only the BLE (i.e....
Hi,
I found a bug in ble_app_gls example from SDK_12.3.0 / s130.
If user enters a wrong passkey, the app ends in a app_error_fault_handler exception and the central keeps...
I think I found the source of many of my recent problem. The print in Segger is going crazy.
I found out that if I increment a simple variable and print it when I hit debug...
Hi,
I am using the nRF52-DK as a device like beacon encodded with the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon.
I want to change...
