Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Dear Nordic team,
I've seen some short video from your booth at MWC 2017 last week. Could you post some photos or at least hint about the product examples you had there...
Hi,
Both examples were built failed in Keil due to exceeding 32K trial limitation. Is there any way to reduce the size? Or any suggestion?
Platform: nRF52DK
Keil uVision...
I am working on a project using a BLE Nano and Nordic sdk 8.1. When I compile my application and flash it to the device my program runs exactly how expected. If I unplug the...
I use the nrf52832.
In the beginning,I can download the code and it works well.
And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
I use the nrf52832. In the beginning,I can download the code and it works well. And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
Hi, i'am working on a custom board on which there is two led drive by a led driver.
The two leds are wiring to be drive by pins P0.14 and P0.15, but unfortunately these...
Hello! I am using a nRF52832 device, along with SDK 12.1.0 and S132 v3.0.0. Data is being sent data through BLE and received on an Android phone.
After some tests I noticed...
I need to have a Central device physically connected (via UART) to a sensor. Data is collected from the sensor and sent to a number of Peripheral devices which use the data...
Take a look at these screenshots. With the trigger enabled, the average current consumption is reported at 13.21uA. With the trigger disabled , the average current consumption...
Dear Nordic,
I want to know if it is possible to send asynchronous data type from a slave node to a master node (master node would be in continuous scanning mode). Reading...
Here is my problem. I want to disable uart when there is no data coming into MCU.
I used IO LotoHi event to enable uart Rx. After finish data receiving, I disable Uart.
...
I've modded the PCA10040 DK for current measurement with an ampere-meter (TTi 1604), using a program which turns an LED on and off every 5 seconds. The measured current stays...
I am using an LG G5 and my co worker let me use a google pixel. I tried using the s132 softdevice along with the BLE UART example code from 12.2.0, I get the device is not...
