Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I've been trying to build the BLE Audio Broadcast source to run on my nRF5340 Audio DKs using the line in as the audio source. I've been developing on nRF52 for a while using...
Hi!
I need to create an application that sends text messages to a private server, such as ptsv3.com.
Could somebody please help me make this application work?
I encountered...
Dear Community,
I am currently working on an LTE-M and NB-IoT project in India using the nRF9151DK and testing the AWS IoT sample. Everything is set up, except for an active...
Hi, We are using following HW and peripherals: - nRF52840 - I2C - ADC - RTC1 - RTC2 - PWM - GPIO - SWI. We are using following 3rd party libraries: - nRF5 SDK v17.1.0 - FreeRTOS...
Hey All, I am sorry if this question may seem absurd or very very illogical, I am not very good at hardware but here I go. So I am designing a circuit around nRF54L15 as my...
Hi for the nRF54H20 the ds says there are two options for how to supply VDDH: either VDDH=2~5.5V with config 1 or VDDH=1.8V with config 2. If my system has 3.8V from a lithium...
Hello community,
I am trying for multiple firmware updates for my NRF5340 DK board.
What I am doing is I have build and flashed the SMP server sample program found /zephyr...
Hello Nordic Community,
I am working on a project using nRf5340DK and need to generate an 8MHz clock signal through a GPIO pin.
Could anyone provide guidance or share...
Hello everyone! :)
I'm having trouble detecting the sht85 sensor using the nrf9151dk. The wiring is good, since I tried connecting the sensor to the Arduino Uno and it works...
Dear Team,
I have a question regarding the Broadcast Isochronous Stream (BIS) / controller timing adjustments.
I am using the nRF52840 DK and NCS 2.9.
I have two devices...
Hello,
I try to understand how the NCS handle the 54L15 partition. When I turned on the mcuboot, I got this report and it is easy to understand:
However, when I use...
Is there any way to test the Direction Finding Central sample code without an antenna array? I currently have two development kits in which I would like to use to test the...
Several of the central examples in nrf SDK v2.9.0
using build target; nrf54l15dk/nrf54l15/cpuapp
produce this linker error:
undefined reference to `bt_conn_le_create...
I'm using an nRF7002DK, SDK v2.7.0, and I've set it up as a BLE mesh node following the Zephyr bluetooth mesh sample . It's running fine, and I'm able to provision it using...
