I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I have a sensor device that needs to transmit every so many seconds. I am looking for a code example to run on nRF52-DK that will do this, sleeping inbetween transmissions...
According to the Gazell using the 1MHz spacing for each channels and the DTM using 2MHz spacing.
Then can we use the DTM channel 0 for Gazell channel 2 to test the Frequency...
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile).
Here is what I need;
The iOS and...
Hi,
Question regarding blog from Thomas Søderholm ( blog.nordicsemi.com/.../which-technology-should-i-choose-to-connect-my-wearable-device-to-a-phone):
Can't you do...
Keil 5.18a forces me to install "missing Software Pack"
I am trying to set up SDK 11, SD312, with Keil 5.18a, but when I try to load an example from the SDK 11 examples folder...
Hi! I have a nrf51 that act as a central and a beacon that is my peripheral, they connect to each other using is_uuid_present but I can't enable notification using db_discovery...
Hello,
I am currently designing a PCB containing the nRF51822 chip and I am concerned about how I will be able to update the program.
I have 2 main questions :
I...
Hi,
I developed an application with Nrf51822 with some bonding need.
No problem with android or using the dongle, but using iOs systems it happens that after a random attempt...
When I add a GATTC in S110-V6.0.0 ,my GATTS stops working,the NRF Master control panle retern ERROR(0x85):GATT internal ERROR Error(0x85):GATT ERROR .Can S110-V6.0.0 run GATTC...
The note on the IoT softdevice says:
"This SoftDevice is a technology prototype only. Therefore, it should never be used in production."
Will there ever be a production...
Hi
I know perfectly it is not possible to debug while the softdevice is enable and the Bluetooth is working. When I try to set up a breakpoint under these conditions, the...
hello there i want to communicate nrf51 and nrf52 using i2c protocol. [https://devzone.nordicsemi.com/question/75218/i2c-in-nrf51/?answer=75221#post-id-75221]
from this...
Hi ,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
The program detail of nrf51 as below:
-- sorftdevice : s130_nrf51_1.0...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
Hey ,
I'm trying to implement a device that waits for the clicks from the user and sends it over ble as notifications.
i have written the header files for sensor . and from...
