Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Device: NRF51-DK
I'm using GDB+OpenOCD to step thru code and it appears that the nrf51 resets itself after calling:
SVCALL(SD_BLE_GAP_ADV_START, uint32_t, sd_ble_gap_adv_start...
I want to make rs485 communication with nRF51822. I gone through the UART code, there CTS , RTS pin are required , but for my case tx, rx,rx enable is enough, and also shall...
Hi everybody!!!
I am making a project which use NUS service and I have confuses in connection mode:
when the central and peripheral do not have data to transfer...
Hello, my question is pretty clear i guess. Is it possible to schedule advertising of 2 different packets on the same chip ?
The way i see it, it should be possible to...
Good morning, I´m trying the example of this post (ble_app_template_with_pstorage_operations_nRF51DK.zip). I have SDK 8.1.0, softdevice 110 and nrf51-dk.
The source works...
Is there any clear documentation to add an external memory to the nrf51822 to store some sensor data. How is the performance and stability when interfaced this way?
Dear all,
I'm working with nrf52832 and SDK 11.0.0.0.
I want to upload SD 2.0.0-7. Download results OK but,
nRFgo Studio, when accessing the unit reports:
Region 0...
I just got the signed bootloader to work with the single bank implementation but had to change dfu_single_bank.c. I believe the change represents a bug in the code.
In...
We are working on a nRF51 device and and corresponding iOS App, and we would like to set the name of the device. The problem is that when connecting with an iPad using BLE...
Hi,
Im trying to use BLE DFU Bootloader from examples. I loaded SD8 and then bootloader via nrfStudio (dont have a valid app flashed), but I cant see the device from Android...
In [sdk10_folder]\components\ble\ble_db_discovery.h , BLE_DB_DISCOVERY_MAX_SRV is given the value 2 .
In [sdk10_folder]\components\ble\common\ble_gatt_db.h , BLE_GATT_DB_MAX_CHARS...
In another thread entitled:
Change in GPIO to start/stop timer and fire interrupt
The following code is used:
NRF_GPIOTE->CONFIG[0] = (GPIOTE_CONFIG_POLARITY_HiToLo...
Hello,
I'm trying a very simple thing; to light a LED on button press. I'm using SDK 9.0.0, nRF51 and SoftDevice 110. However, button handler is not firing.
So, APP_BUTTON_INIT...
