hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi Nordic,
We are working on Android and iOS apps. Currently using S3 with Android 4.3 and Note to communicate with nRF51822. Baud rate of 19200bps for our serial communication...
Hello,
Is it possible to increase the accuracy of the advertise interval? Im attaching an oscilloscope screenshot showing the S110 device advertising with a 20ms interval...
Hey All,
I am working on a board that is based on the nrf51422. The system goes to sleep and gets woken by an interrupt. One of the programmers claims to have managed sleep...
We use nRF51822 with S110 as a peripheral connected to iPhone master and looking for RSSI.
RSSI with correct value is received by the peripheral application every about 1...
Are there any sample applications that use a joystick press as an interrupt instead of a button press? The dev board I'm using uses the nRF6350 display and I was wondering...
Hi
I used the example from nrf51822_v4.4.1.31827\Board\nrf6310\spi_master_example for my PCA10001 board, as I know the pins configured in this example are for nrf6310 board...
Does anyone know how to implement a wrist watch LCD display? I mean a bare LCD Display, without a pre-build driver (I2C). Can I do it directly or I need another IC to drive...
Does anyone have any solid numbers on the maximum throughput achievable on
the nRF51822 USB dongle that comes with the nRF51822 Eval Kit?
Application - OTA protocol Gazell...
Dear Support Team,
currently I'm working on a custom board which contains the NRF51822_QFAB_A0.
I installed the softdevice (not the most recent version, but a version...
Hi,
I have bought nRF Beacon Kit, and I have downloaded "nRF Beacon Android 4.3.zip", but I can't find nRF Beacon Service source code.
Where is it? Please tell me.
...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
it register a handler, what about restart and run pstorage_register again, how it insure everytime we get the same address for our content in the flash?
before pstorage_register...
I'd like to measure the voltage of a lithium ion battery every minute or so in a way that's highly accurate. I need to do this without using the Soft Device because a) I need...
