Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
We are using the npm1300 PMIC to run the nrf5340 VDD at 1.8V. If we connect D+ and D- from the USB port directly to the D+ and D- pins, will the USB peripheral...
I am developing a custom nrf5340 board design, that is using the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module allows all...
Hello,
I am purchasing a RAK4631 module, and am looking for an alternative for the J-link single step debugger. I saw that this product had a o n-board SEGGER J-Link debugger...
Hi ,
I am exploring the peripheral examples from the nRF5_SDK_17.1.0.
I am testing the example code "flash_fds" from the peripherals. I am able to compile the code without...
According to developer.nordicsemi.com/.../migration_sysbuild.html , the config variable SB_CONFIG_BOOT_SIGNATURE_KEY_FILE and SB_CONFIG_BOOT_ENCRYPTION_KEY_FILE should be...
Hello,
I have a custom board based on a nRF9160 SiP. It uses a shared antenna for GPS and Cellular, based on this : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_033...
Hello,
Installing a new computer with de dev environnment I am finding that NCS1.9.2 is not in the available releases.
Is there a reason for this?
Thanks for...
Hi,
I have a customer in Guernsey that received one of our Thingy91 hubs and he's not able to connect.
Here is some troubleshooting facts :
- when he moves to London...
Hello,
I just received a new NRF9160-DK board and I am surprised it has the 4 leds blinking all along.
What does that mean?
I have not found any of this in the startup...
I need to use UART0 of the nRF9161 via Tx(P0.27) and Rx(P0.26) for serial communication. There is no CTS/RTS signal.
I used the code from Lesson 5 of the DevAcademy. i...
I'm developing with nrf connect sdk.
I have an peripheral IC with a mcu interface enable pin. This product is very focused on battery life. The peripheral IC has higher...
Zephyr / SDK 2.1.2 / nRF52833, acting as BLE peripheral. My system consists of multiple peripherals, and I want each of these peripherals broadcast its own unique MAC address...
Hi
Is any of this antennas supportet or certified in Norway ? I know thingy 91 use trio mxtend from Ignion.
But is run mxtend certified or do I need to certify it ? Its...
Currently, the nRF5340 Audio is set up and running as follows: In CIS mode, the audio source is I2S
Gateway side: nRF5340 Audio DK I2S settings are default Headset side...
Hello,
I'm running into a problem where every time I run the asset tracker the modem reset loop is triggered and I have to wait 30 mins before I escape. I've read the...
