Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I wanted to get FOTA running on a PineTime devkit board (nrf52832) just to test and see if it works, but am getting the following error message:
/opt/nordic/ncs/toolchains...
Hello
We have developed a device based on the nRF9160, one of our potential clients asks us if the device has High Priority Access, he says that this information should...
Hello!
im trying to write chunks of bytes to an sd card in a non blocking style. One possibility im pursuing is to use SPIM, where the actual writing is done by DMA-Controller...
Hello again,
I am putting together a device that need a lot of local non-volatile data and uses a lot of flash on my NRF52833. I am running NRF Connect SDK 2.6.0. I'd like...
Hi there,
I'm encountering an issue while attempting to establish an Internet connection on my Linux machine using the nrf9160 DK SLM (2.6.1) application. I've flashed the...
Attempting to get up and running with the basic zephyr lvgl demo found in `zephyr/samples/subsys/display/lvgl`. Text appearing on the screen is of poor quality but still legible...
Hello,
We are currently developing a WiFi library and just started on implementing HTTPS and ran into some issues. Since we don't have enough flash and memory for using...
Hi everyone,
I’m currently working on setting up Azure communication using the latest SLM version for PPP (Point-to-Point Protocol) support. Here’s the configuration I’m...
We have a Waveshare display and a npm1300dk and I wanted to know the proper way to add the npm1300's config.overlay file, generated by nrfConnect's PowerUp, to the west command...
Hi,
I faced some issues regarding multiple IRQ_CONNECT being onvoked on the same irq and I went into this post :
LPUART nRF5340 fatal error - Nordic Q&A - Nordic DevZone...
Hello! I am using nRF Connect SDK 2.6.0v. I created a west workspace and i want to make custom board. I took reference from Devacademy nRF Connect SDK Intermediate Lesson3...
Hello Nordic
Use NRF52832 、 NCS 1.6 、“zephyr\samples\basic\blinky” sample.
In hardware, my board doesn't have a low-speed clock, and the reset pin is floating. Therefore...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
I am using nRF52820 and the SDK is nRF5_SDK_17.1.0_ddde560. When setting advertising data, I am trying to enter the chip's BD address for individual identification. Is there...
