Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
I'm trying to use an ILI9341 display with nRF52840 in Zephyr (v4.1.99). The build fails with multiple errors about missing Devicetree properties when compiling display_ili9xxx...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
I have been trying to use the Nordic security backend with the MQTT library (TLS transport). However, after I finally got everything to build , I am now getting runtime errors...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
I am using 2 nRF528400DK boards. Each board has a unique BLE Mesh sample loaded. The samples were made by modifying the default mesh sample provided by zephyr. One sample...
Hi support
I am developing code for the application core on the nrf5340 and testing this on an nrf7002dk dev kit. I am using sdk version 3.0.0. The code needs to read from...
Hi, How I can use/install nRF Util software ( device, nrf5sdk-tools, etc ) in a lab without internet access on MacOS machine ? I can download ' nRF Command Line Tools' but...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
hello everyone ...I am working on a project that uses the nRF52840 IC. I would like to implement a power-down mode to reduce power consumption. In my project, I am using BLE...
HI Teams
I found in the datasheet that the UART, I2C, and SPI on the nRF5340 share the same set of IDs. Does this mean that these three buses cannot be used simultaneously...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
I am currently evaluating the Channel Sounding functionality for indoor localization. I would like to check how much Energy my Initiator and Reflector consume for...
Hello, I am currently developing on a custom board based on the nRF7002 + nRF5340. The SDK version is v2.8.0, and the development is based on the BLE Provisioning example...
