I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
Hello,
I am running windows 10 and started the DevAcademy lesson 1, exercise 1 and exercise 2.
Up to exercise 2 item 4 (add a build configuration) everything went fine...
Hello i am using an nrf52840 s140 and i am trying to write a specific event when takes place to the usb port. I am using the usbd_uart example.
It works fine for the first...
I used Nrf9160 to develop a product. Until yesterday, I had been able to connect to the nb network normally. But today, I found that my device could no longer register to...
Hi, I'm looking for help installing the nRF Connect for Desktop 3.12.0.
I've managed to unpack the application EXE and have picked out all the required pre-reqs to do the...
Hi,
I have a problem, When I first initialize Bluetooth and then initialize FDS for writing, it will fail. However, if I first initialize FDS and write data ,it is OK, then...
Hi,
We develop a custom gateway in which we use iMx6ULL and NRF52840. Both are connected over full UART.
We use this NRF52840 as a BLE HCI controller by flashing the HCI_UART...
I'm following the Nrf Connect SDK tutorials on YouTube and I am at step 3 ( nRF Connect for VS Code, 3: Building an application & Exploring windows ). When creating the build...
I have developed an image based on the AWS IoT example which runs on a custom board. The custom overlay exposes some additional UARTs, LEDs, buttons, etc. in custom pin locations...
hi support team,
customer is asking how to add keep alive time in https request header,
i was trying to do this command as below: adding " Keep-Alive: 60\r\n" in XHTTPCREQ...
Hi there!
I've been digging through the code base but could not find a compile option to enable LOG_DBG() type output so that I can observe the JSON formatted packets sent...
Hi,
1. Please solve the problem of high network current registered to nRF9160 (test environment: no network signal)
2. Rf signal: the test current is normal. See Appendix...
Hello,
I implement my own DFU master in nrf52 using SDK11 to replace use of Nordic mobile App. Target to upgrade is also nrf52 but with SDK15.
I have difficulty to get...
Hi,
How do I set the SPIM3 parameter so that MOSI is low after SPIM3 has sent a byte 0x01?
The test environment
DK PCA10056
SDK :sdk17.1
example :spim3
Thank...
Hi,
How to enable NRFX_LOG_INFO?
I ran the following test, but no nrfx log was found
example:D:\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056...
