Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm not sure if this code I inherited is using k_poll_signal correctly because it seems like I can handle it in a much simpler way with an atomic variable.
The below code...
I want to use the lsm6dsox IMU on my Adafruit feather nrf52840 sense board, and I should use other I2C, other than p012 and p011, to not have a problem with the other IMU...
Dear team,
I am not able to flash the nrf5340 audio application (gateway) to the nrf5340 Audio DK using SWD from nrf5340 DK. I nrf5340 DK outputs 1V8 logic.
I can see...
I am using S132 in the Segger IDE on an nrf52832.
I am using SDK version 17.0.0_9d13099.
When I call sd_ble_gatts_hvx() from within a GPIOE ISR (externally pin triggered...
Hello,
Looking to see if there is a pinout TABLE for this package. I've seen the schematic drawing already but looking for a table format which is more user-friendly when...
I've set "NRF_SDH_BLE_GAP_DATA_LENGTH" value to 27 on peripheral side, and it've changed to 251 after connection. On the central side, the value is fixed as 27. I believe...
Hello,
We're currently developing PCB with nRF5340_CLAA SoC. For specific reasons, main supply voltage was changed from stable 3.3V to 3.5V that comes from DC/DC converter...
I recently followed the instructions laid out in the "nRF Sniffer for Bluetooth LE" User Guide version 4.0.0 and having trouble seeing the nRF Sniffer interface in Wireshark...
Hi,
I am trying to implement bluetooth uart peripheral for nrf52811. I try to learn the code from example and want to check the result on my board.
When I build the...
Hi,
I'm on NCS 1.9.2, and I'm having a unexpected behavior on the consumer thread of a k_fifo. The documentation states that the k_fifo_get routine removes a data item from...
Hi all.
I was planning to build ble example and combining it with I2C, but I found this error
I check several previous posts on this forum before and solution...
Dear Nordic,
I am a beginner. I would like to transmitt the sensor data from a Lora32u4 board (End-node) to an nRF9160 Thing Plus (As a gateway) connecting to Lora SX1276...
Hello Nordic-Support Team,
i have a question regarding the Application Timer as said in your documentation here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
Hello,
i would like to ask you for advice how to correctly process the connection status information from the modem. Our application is sending telemetry data to the cloud...
