Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
in the nRF52840, SPIM3 allows for high speed >4MHz communication. But I cannot see if there are dedicated pins specific to this mode, or can i map any pin to the SPIM3 high...
Hi Team,
As part of our requirement we need to fix the Advertisement to one fixed channel instead of altering between 3 channels like 37,38 and 39. If we have any sample...
Hello,
Using own BLE stack here (not SoftDevice) and having troubles with LL certification test cases with particular problem:
the tester establishes connection and...
Hi,
I would like to take current & power measurements of the nRF52833 SoC with the desired firmware file flashed to it. I am testing an application that uses the CPU temperature...
We are trying to make it so that we can permanently make one channel on the BLE module only for advertising while having the other channels flexible for other needs.
Hello, I have nrf52DK (nrf52832-PCA10040) and I wanted to test the Peripheral example in the nrf Connect SDK. I have built the project for nrf52DK_nrf52832 and then flashed...
Hi,
I am developing app using ant softdevice s212. I want nrf52832 to enter system off and stay there until interrupt from sensor occures. This interrupt is connected with...
I use nrf5340 to build esb project, I use the following code to scan rssi of different channels, but I read the value of NRF_RADIO->EVENTS_RSSIEND is 127, I hope you can tell...
Dear ,
How do I enable DCDCEN mode if I am using NCS1.8.0 SDK? Is there any Kconfig setting I need to perform to make this available?
Thanks and regards, Kevin
Hi,
Just wonder does NVS only use half of the configured size? I have configured the nvs_storage size = 0x2000 ( 8192 bytes)
So sector_count = 2 (4096 / sector)
When...
Hi Team,
We are in process of developing pairing mechanism for our peripheral device. We are considering using NFC for OOB. Here is what we think we should be doing: ...
Hello People,
I am working on a custom board and while trying ble_app_uart example code instead of the advertising name given in the code the device was showing "DFU_TARG...
Per the documentation on multi image builds , a child image folder that contains a <board>_<revision>.overlay it will be merged with BOARD.dts but I cannot do the same for...
Hi,
I'm working on a project that utilize the MAC library.
Coordinator with non-beaconed mode was previously used in the project, however the NRF 17.1.0 SDK is not compiled...
What is the threshold voltage on a nRF52840 GPIO to detect low level powered with 3.3V?
Can't find it in the datasheet. High level threshold will be 0.7*VDD right? 0.7 ...
