Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
device: nRF52832
SDK: nRF5 v15.3.0 (s132)
Soft Device: 6.1.1
I am trying to read multiple fds records and transmit them to the central device (nRF Connect on android...
SDK: 15.3.0
I have developed PCA10056 board based on CLI example.
I tried to print debug strings.
but, [00: 00: 32.310,668] <warning> app: Prints backends flushed repeatedly...
Hi,
I have developed BLE mesh by using nRF52832 with Mesh SDK v5.0.0. Now I am trying to implement the light switch client example.
In order to reduce the current consumption...
I'm running into an issue in which I cannot initialized the I2C drivers on an Arduino Nano 33 BLE (nrf52840). The output from error logging is
I have this prj.conf file...
Hi. I am using timers and PPI to do frequency counting.
The basic process is for 1 PPI channel to incriment a timer, and then a second PPI on a second timer to stop the...
I build device based on Fanstel module BC833M with pcb antenna.
Communication with this device is very bad. I have test the same code in BC833M and origin Nordic devkit...
Hi,
First off, I'm very new to the nRF52 development so I'm suspecting to have done something wrong...
The datasheet of the nRF52 832 states a current consumption of 0...
Hi,
I have been tryring to identify the characteristic who is requesting a read. To do so, I implemented the read authorization request. Here is my code:
Basically...
Hello,
I'm trying to receive an inverted UART signal on the Arduino Nano 33 BLE (NRF52840). I've been able to invert the transmit signal okay using two GPIOTE channels and...
in ble send data period ,nrf 5340 CPU seem to be shared only by ble send
data ready and data read in ble not send period can equal ,this mean every data come from ecg chip...
Excuse me:
I'm testing the maximum rate of ble_app_uart。
1、Can the nrf connect app on IOS initiate the update of MTU and PHY?How to update MTU and PHY on IOS nrf connect...
I use nordic5340 SPI read ADS1298R ecg data, using nrf5340 p0.13 to connect ADS1298R data ready pin . when ADS1298R data ready pin high to low mean ADS1298R data ready .i...
