I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
Hello, I tried to run the following command on my nRF52832 today and it reported an error.
The operation before the error was: I enabled APPROTECT, and when my colleague...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
Hi Team,
I am trying to make RTT in debug terminal instead of debug serial port i was add all rtt files in the project tree but it was not shown in cmsis configure wizard...
Hello everyone,
I am trying to implement ECDSA_P256 in my code by using the nrf_oberon libraries.
What I have to configure in order to use these functions?
Regards ...
I use nRF52810 SoC to forward data between BLE and UART on our product. So I initialize UART interface and set some GPIOs once enter the "main" function in my codes. But we...
Sdk: 1.6
Modem fw: 1.3
Hi,
I am testing the GPS + supl example on our custom board. I am sitting indoor close to a window so satellite reception is affect.
the example...
Hello,
I am Working on the nRF52840 custom board.
To drive the motor and buzzer I am using a PWM driver in that when I set duty-cycle 20 percent then the output of PWM...
Hi guys,
Using the PPK 2 board I have noticed that sometimes my device does not go into deep sleep mode between two tasks. I had to implement a lot of flash operations using...
Hi Team,
Currently we are using 52840 soc with softdevice s140_nrf52_7.0.1_softdevice.hex.
We want to migrate to 5340 for BLE 5.2 features, we would like to understand...
Hi,
I need the SAADC of the nRF52840 to do the following:
It should sample two channels as fast as possible for a certain time (or for a certain amount of samples)....
