Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hiya!
I am writing code to add support for USB on the NRF58233/58240 to MakeCode. MakeCode relies upon WebUSB. At any point, a user can close the website which causes...
I noticed the minimal b0 immutable bootloader build does not fit anymore.
I used the example here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
Hello,
We are using NRF52832 to design a loss preventer product ,can you help to review the design SCH and PCB layout before PCBA making ? main including RF desing , GPIO...
Hi, I was trying to a project that includes edge impulse and nRf5340DK. I successfully run the example project t they provided and now try to use the library provided by edge...
Trying to do DFU over ZigBee, but nrfutil failes:
Gets this problem constantly. I have check all the examples and everything, doble checked all parameters, but always the...
Hello.
I am trying the SEGGER Embedded studio's open nRF connect SDK project, but it fails with an error like the one in the image. How can I make it succeed?
SEGGER...
I am doing something really really crazy, that's writing some application on PC using opcode serial port for configuration a light switch server (maybe light switch client...
Hey all,
I've been using the SDK for Thread for quite a while and got all the basic stuff up and running with Thread and the nRF52840DK, RPi Border Router, etc.
For example...
Hello, I'm working with nRF5340 DK with Zigbee communication. I'm getting RSSI values between 0-255, but I'm more interested in the value in dBm, so I would like to convert...
Hello,
I developed the code on nRF52-DK with Segger.And also I want to program this code to MDBT42Q chip with nRF52-DK.
What are the circuits and software programs where...
Hello, I' trying to use the Serial LTE Modem application on an Actinius Icarus board. I configured the nRF project for the correct target, enabled COAP support, set Nb-IoT...
After upgrading the nRF-Command-Line-Tools from 9.8.1 to 10.12.1 the RTT output of JLinkRTTClient stopped working when doing a nrfjprog --reset. Interestingly it still works...
Hello, i've tested dfu process from secure_bootloader with different app examples with success (ble_app_blinky, ble_app_uart, even a custom application) but, when I try the...
Hi, I want to use normal GPS data (not AGPS) to send to my MQTT server.
I work well with MQTT_Simple to send sensor data to my server.
I see a GPS example in /nrf/samples...
Hello,
I have application that is sending data over BLE every 5 minutes.
I want to implement DFU using BLE. I don't have any single button on my device.
What should...
