I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Nordic team
I am developing a BT mesh network project, which be implemented by nrf52840. Right now I am designing the node PCB. I want use the No.4 reference circuit...
Hi,
I tried to implement my custom service.
I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example
For SDK 15.0 it works...
I'm attempting to connect an SDcard (micro SD) to an nRF52840-DK via a breadboard setup. I'm running Zephyr and it appears that configuration is to be performed via device...
I'm trying to investigate whether I should ditch BLE in favour of Gazell and ShockBurst (to avoid the $8000 Bluetooth.com fee)
I've noticed that Gazell has no entry in the...
Hello,
I've got this Thiny:91 demo working nicely, but what I'd like to do now is only measure RSSI.
Is there firmware to only do this?
Like send AT commands only to...
Hello,
I've been trying to perform a dfu to a target Nordic device over Bluetooth using an nrf52840 dongle distributed by Laird, however whenever I attempt to run the command...
Hi guys,
I am trying to create a zigbee mesh with 10 devices with 1 coordinator and 9 routers (all are nrf52833 based custom board). I can create a mesh network easily with...
Hi,
I understand that white list can be enabled at the peripheral side. I also know that if white listing is enable on the peripheral side then it wont respond to centrals...
Hi All !
Hope you are doing well !
I have tested some examples using SDK 17.2.0 and it worked fine ! .IDE i used is SEGGER IDE . Now i have a question that my next HW...
Hi,
I'm testing the USBD BLE UART Example with nRF52833 DK, after programming the app, the LED3 keep it off all the time as followed.
In the device manager, I can see...
I'm porting from 1.2.0 to 1.4.2. I'm using mqtt_simple as a baseline but I'm connected to Google Cloud. I successfully create a socket;
net_mqtt_sock_tls.mqtt_client_tls_connect...
Hi:
Now i am development the OTS, the default connect parameter is:
interval_min = 24 （30ms） interval_max = 40 (50ms) latency = 0 timeout = 400 (4000ms)
But i got the...
Hi,
I want to receive UPD message on my nRF9160-DK. I can send UDP messages from my Nordic device to a server and from that messages I get the public IP address of my module...
I want to use I2S on nrf9160. I found some code on the its user manual and try to run in my project. But when the device is running, it always reboots. What other configuration...
Hi,
I am developing a project related to transferring audio in low energy Bluetooth. I came across nrf connect sdk is the best one for LE Audio transmission
But I am familiar...
