I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
The ncs/v1.4.2/nrf/tests/unity/example_test project does not seem to build for the emulated native_posix board when I try:
First it was complaining about Ruby so...
We am using SDK 16.0.0 with S132 v8.0.1 on an nRF52832 custom design.
We have ported the secure boot loader to our design and we can perform buttonless OTA.
The issue...
I am looking to use the L2CAP in the basic form. I see that there is the Experimental OTS example in SDK 17.0.2
this only uses the S132 Softdevice. I am looking to target...
Hi,
I'm using PWM on a nRF52832 (nRF52 DK) with SDK 17.0.2 . I have 3 PWM channels configured to LED2, LED3 and LED4. Below are my questions. I'm using PWM to dim the LED...
Hi there,
I'm starting a new project using an nRF52840 that interfaces with a Quectel BG95 modem with AT commands. Ultimately, I need to use MQTT to an Azure cloud environment...
We are measuring advertisment current consumption with CODED and it's averaging about ~400uA. Advertising on 1MBPs is right around where it should be ~30uA. Advertising interval...
Dear Nordic engineer.
I am using nrf9160.
I follow the instructions to download Fota using AWS upload file update.bin.
After the device has downloaded the file and receives...
WHY ARE SO MANY UN-NECESSARY LIBRARIES INCLUDED IN SIMPLE EXAMPLES?
I'm using nrf52 for a consumer device. Just loaded up the blinky example (under the peripheral folder...
Hello everyone,
I was trying to compile ble_app_uart code in segger embedded stdio but sample code not compile this sofware any configuration setting i need to change.....
Running nrf_drv_saadc_calibrate_offset() doesn't seem to work. I'm monitoring a 3v battery. Shown below is the debug output where the calibration is run after the event number...
Greetings,
We are attempting to install the nRF Sniffer program onto our nRF52833 DK as directed in the Nordic instructions. We've installed the nRF Connector S/W as well...
Hello All,
We are in the evaluation phase to implement openthread network in our gateway using nRF52840 as NCP device.
We require to have the number of end-device supported...
Hi,
I used to have a URL link for checking ibasis SIM card, such as devices, balances, etc. Now, I cannot find. My SIM card is from Nordic, so the login for ibasis account...
Hi Dev Team,
I am building an application wherein I need to send commands from the Cloud to a Thingy91 device. I tried out the cloud_client sample and I was able to send...
I have seen this problem posted several times in these forums but none of the existing solutions sit right with me.
I have an NRF52840 (using a UBlox BMD-340 dev board...
