I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello
When I send data over BLE, I got this messages in debug terminal.
<info> app: Debug logging for UART over RTT started. <info> app: Connected <info> app: Data len...
I have seen other post on this issue but they are not helping. I am using the bmd 330 to run ble_app_uart. It compiles and advertises correctly but does not send the tx and...
Hi,
I am facing issues in Flash Data Storage (FDS).
Here, nrf_fstorage_write function is returns with NRF_SUCCESS but not writing in actual memory location. While nrf_fstorage_is_busy...
Hi. I am now at the stage of creating a new project. I want to include DFU over the air support in it. So, how can I do this using the example of two projects (secure_bootloader_ble_s132_pca10040...
How do you use the nrfx_temp driver in a project? I'm on SDK 17.0.2, segger, and an NRF52840-DK board. I see the old HAL temp sensor is deprecated and it seems to always return...
Hi,
I have been using a certain 16MHz oscillator up until now without any issues, and now wish to replace it for logistical reasons, what kind of testing are recommended...
I'm designing a product which incorporates a magnetic sensor (MMC5633) and a Bluetooth microcontroller (NRF52832). The sensor and bluetooth chip share the same ground plane...
hi,
We have some products that have been sold out(hardware:52832,software:sdk13,softdevice:s132_4.0.3).I want to upgrade their sdk to 15.3 through DFU.I learned in the official...
Hello,
I'm trying to modify the current ASSET_TRACKER of SDK v1.4.1 to get it to work in my own server on AWS-IoT.
I'm wondering if there is any documentation about this...
use SDK17.
central uses nRF52832 and peripheral uses nRF52810.
I want to implement the exchange of data with each other.
First, the central scanned and connected.
...
While using NRF52840 SDK with twi_scanner i am able to see i2c address 0x68, but while using zephyr unable to get the data.
I have seen I can configure i2c pins in board...
As I'm new to the BLE, I'm trying to make use of examples enclosed in the nRF5 SDK.
Now, I found that there exist several functions that seem like do similar things and...
1.4.8 programmer is complaining 'Error while getting readback protection' when connecting to the BL651, 453-00005.
Used to work.
Seems to connect OK to BL652-SA-01.
Hi,
We have a product using NRF52840 ready for production. In factory production environment we want to validate the product for PCB, product assembly etc failures and also...
Hi,
I am going to implement a PPI to connect GPIOTE event in with TIMER COUNT TASK, and then read the count from CC[0]. But the count in CC[0] never updated.
Basically...
