I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hallo everyone,
I have interfaced LIS3DH with nRF52832 and reading a value as below
X 230
Y 249
Z 54
How to convert this value to standard acceleration unit...
I am using the nRF5_SDK_17.0.2 "examples\ble_central\ble_app_blinky_c" example to start with my device.
It works using "init_scan.connect_if_match = true"
However, my...
Hi, all
I'm using nrf52832 pca10040, s132
I've asked several questions, but I haven't found a solution yet.
I want to send data through uart to the custom board.....
Hi,
I am trying to extract the static MAC address from a 52832 using NCS.
I do not want to try to read directly DEVICEADDR[0] or 1, but use a clean function.
I tried...
Hi People, I hope I can get help here or get pointed to a right forum where this can be answered.
I am using u-blox NINA-B306 (based on nRF52840) in one of my custom made...
Hello,
I am using the address resolution function getaddrinfo. Everythink looks fine, however I am wondering which DNS is used for that and if it is possible to update the...
Hi,
I am trying to do a quick PoC to connect some thread nodes to the cloud through a BorderRouter(RPi3b+ running Nordic Border Router, connected to a router using LAN...
I started with the peripherals/spi example, and am now trying to update to the recommended nfrx drivers. I can get the spi working fine, but I can not get the linking to work...
I am setting some manufacturer specific data to broadcast using sd_ble_gap_adv_data_set().
The data gets sent out perfectly when the advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
In my application, a host co-processor controls when to start/stop advertising, connect etc.
I've noticed that soft-device command are state-dependent, e.g. calling ble_advertising_start...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
