Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi,
I am using nrf52810 and want to use the same SPI module as an SPI slave and master in the same application. Is it possible to change the SPI module role on the fly?...
According to https://devzone.nordicsemi.com/f/nordic-q-a/3497/sd_ble_gatts_value_get/12659#12659 , it appears that sd_ble_gatts_value_get() can only return the maximum length...
Hello,
I'm new to sniffing BLE. I'd like to determine the min and max connection interval and other connection parameters (MTU, slave latency, supervisory timeout, etc....
I am just starting development of a BLE mesh product on the nRF52840 using the serial demo on the nRF52840DK. By default PERSISTENT_STORAGE=0 in the demo so the nodes forget...
Hi,
I have a Unix time stamp value stored on the Nordic board that comes from a GATT connection.
I am using SDK 15 s140 pca10056 NRF52840-dk.
I need to update this value...
I am using nrf52840 dk for zigbee project with two xbee modules. One xbee is configured as coordinator and other as end device and nrf board is supposed to act as router....
I use nRF52810 + 15.3.0 s112 to develop. After the equipment upgrade is successful, I power up the equipment again, and the equipment is always in DFU mode.
For some reason it seems that the TWI master does not generate a NACK. As a consequence, the TWI slave keeps sending data. I have managed to create a very simple function...
Hi
I have a really strange issue with an NRF52840. I'm using it with an MPU-9250 connected via TWI. I've modifed the excellent library:
https://github.com/Martinsbl/nrf5...
I want to use RTC handler , so I used NRF_DRV_RTC_INSTANCE.
I use SDK 16.0.
" 'NRFX_RTC"_INST_IDX' undeclared here (not in a function) ; did you mean 'NRFX_RTC_INT_TICK...
I've been reading into the "nRF5 SDK for Thread and Zigbee v4.0.0", and I wondered about the limitations , in specific
is that a hardcoded limitation, or does it require...
Hi I programmed the nRF mesh experimental dimming example on the nRF52832 chip. I noticed that, when using Bluetooth Mesh provisioning apps (I've tried several to verify this...
I am trying to setup a PPI channel to trigger the SAADC in simple mode. However, it appears as though the SAADC module is disabled after every read. I.e. if I write:
...
I am unable to flash the DK board facing issue " Failed to Connect to Target. No idcode detected. Please check connections and Target interface Type."
DK Board Details:...
I am using LSM9DS1 IMU, nRF52840 with SDK v16.0.0. I configured the IMU to raise an interrupt when the FIFO buffer be full by writing to register INT2_CTRL the value '0b00011000...
