I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I am using the nrf52 Dk with nrf52832 chip and i want to write bulk data onto the dk and then when i read the dk from the mobile app nrf connect, i want to see the written...
Hi,
I am trying to integrate the DFU service into the ble_app_uart example. I am using NRF51822 with SDK 11. I was able to successfully run the ble_app_hrs with dfu. So...
Hi. I'm using 2x nRF52840 DK's + eero pro.
I've been noticing some stability/longevity issues with examples/thread/freertos_coap_server in nRF5SDKforThreadandZigbeev3209fade31...
Peer Manager in recent SDKs supports up to 20 peers but SoftDevice functions like sd_ble_gap_whitelist_set() and sd_ble_gap_device_identities_set() are able to handle up to...
Hi, I am trying to get BLE packages with the nRF52840 Development Kit without using Wireshark or other external app. Does anyone have any solution? Thanks in advance
I have followed this tutorial from this link but cannot get it work.
I have 3 loop. For the first loop of sending data it will have a delay about 1s and until 2 finish...
A%dBBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX = 40bytes
1) In Termite:
Data is complete and in sequence when until 6 only.
A0BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...
I have 2 message order by sequence and between each of them have delay 2s. for Example
How should it work
A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX
Delay 2s
A2BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...
Hello Nordic Support.
it was first time i tried to set up zigbee project based on 52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. and now i got question...
...
Hello,
I want to design my board using Raytac MDBT42Q-AT-UART module which has nRF52810 QFN SoC inside.
I need BOM with P/N and make of components which are used in...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) I want to configure Advertisement channels...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
Most of our devices are Peripherals. To control them, we will relay...
Hello everyone,
I already posted this on the Segger Forum, but rarely I get answers there, so I hope someone have a solution to this hellish problem! I have been happily...
Hi Sir,
I am working in nRF51 package for interfacing BLE. In general, I have doubts regarding BLE concepts.
1. How to calculate the maximum amount of BLE packets...
