Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi,
I am troubleshooting on a nRF52810 that fails to erase/program. The device has been working in our product with a application software, but now it will not program....
Hello,
I want to enable the scanning with name for the first scanning of the device and after connecting to that device its address will be saved. After disconnection with...
I'm interested in using the nrf9160 as a drop in replacement for my current modem and GPS, where a host mcu would use AT commands or something similar. Has anyone attempted...
Hello,
We want to capture image data which is coming on parallel port on nRF52840 dk. The camera sensor we are using is OV2640. The parallel port (8-bit) data is coming...
Hi,
I am getting error while trying to configure Mesh node. I am using Light switch server example and configure through nRF Mesh Application. Attached some screenshots...
I'm trying to test long range beacons with coded phy on the nrf52840 dongle, so I've set out to turn my nrf52840 DK into a beacon scanner that will spit out data over uart...
Hi Sir,
I am use NRF52832 BLE to UART function, it was working good.
I am refer ble_app_hids_keyboard_pca10040_s132-nrf52832_xxaa example project to add peer manager,...
Hello,
I am a newbie to the Nordic development ecosystem. Just purchased a nRF52840-DK board and followed the instructions here:
https://infocenter.nordicsemi.com/index...
Hello,
Is there a way I can run JVM on nrf51 or nrf52 series devices? I have been searching the forums and did not find any updates on the same.
Any OS like embedded linux...
Hi,
We are currently in development of an IoT solution using the nRF9160. We are doing a set of EMC tests to ensure electromagnetic compatibility of the device. The test...
Hello,
I am trying to transfer a signal sampled on AN0 (P0.02) at 16kHz via Bluetooth using an ATT MTU of 247 and a 2MBPS PHY speed. The basis project used is examples ...
Hi, I am interested in using the NRF91 in our new products. So far I have modified the Asset_tracker example to send my custom data instead of sending the "sensor data". The...
Hi.
I have a question related to the Zigbee SDK's "On / Off Switch" example.
Studying the example, I cannot understand how to activate the "light_switch_send_on_off" function...
