Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi!
I am using the Segger embedded Studio with PCA10056 successfully. Now I have to evaluate LARD DVK-BL654 (because it has external antenna). I found a guide which says...
I am trying to flash my custom board that uses the Raytac nRF52840 via SWD. I am trying to flash a custom bootloader onto the chip; however, JFlash is giving me an error....
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi there, I'm using nrf52840 with OpenThread SDK and I wanna know, what is default radio mode of this device? Because we also have another project with Bluetooth and we observe...
SDK15.0 whitelist hardfault
when setting the sd_ble_gap_device_identities_set using the iOS nrfConnect the non DK board hardfaults.
On an android device all works fine...
Hi,
I'm adding some custom buttons to the NRF52-DK and I've been playing around in PCA10040.h. So far, I have everything working with 4 buttons. The DK can connect to...
Dears,
Now I am using nRF5_SDK_15.3.0_59ac345 for my project on nRF52810.
I found a bootloader example at
\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble...
hello, I am trying to integrates saadc & bluetooth because in my project adc sample values are comming from sensor & these values is send through bluetooth_uart app. so can...
Hi,
I'm in the process of evaluating the nRF9160 DK and this I want to be able to control the diferent peripherals on the DK so I can reduce as much as I can the current...
Dear supplier
I want to read 10 heart rate sensors that are connected to 10 person's bodies and then display them on TV. How can I do it?
Can I use nRF52832 chip? Can...
Hi
I am using nRF5_SDK_15.2.0_9412b96 on pca 10040
I am storing over 2000 ADC readings and then printing them out once my test is complete. I get "Logs Dropped(x) " messages...
Hello
I am writing a program using SDK 15.0.0.
I'm trying to merge SPI and TWI programs into BLE programs.
I used keil before to confirm that each program was working...
Using Ozone v2.54, if i halt program execution and then resume again, I get a NRF_FAULT_ID_SD_ASSERT fault, with info = 0, pc = 0x142CA.
softdevice: s132 v4.0.2
The error...
