I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hey everyone
This is sumanth, I am working low power node in mesh networking, I followed the procedure mentioned in below link for building and flashing
https://www.nordicsemi...
Hi I have a device which can get RSSI value from other devices.
But how do we get RSSI of my device itself.
i.e How to print RSSI of local device on the same device terminal...
Hello everyone,
Today I worked on custom bootloader and according to the article infocenter.nordicsemi.com/index.jsp I tried to load output hex file from IAR on board via...
I want to add a new ble service in hrs example(sdk15.3),I build and run the hrs example.and then I open the terminal emulator, but I can't find anything.I try to click the...
I want to use nRF52840 BLE with STM32F745ZG microcontroller and using atollic studio for coding. is it possible to use nRF52840 with the microcontroller? if it is possible...
I'm using SDK 15.1, nRF52 in custom units, toolchain GDB, addr2line
A little background -
We use System off mode and then use a button press to come out of it.
Before...
After doing a detailed review for the datasheet for nF51822, I can find no input leakage current specification for the digital inputs or ADC inputs. Where do I find this specification...
Hello,
for current consumption measurement of our PCBs, I created a special software. This software does boot up, puts SPI FLASH in power down and go to sleep forever. All...
Hi, Sir:
I am using nRF9160 for development, I would like to complete a COAP client,so I need to refer to ......./nrf/samples/nrf9160/coap_client. I installed NRF_Connect_SDK...
Hello, LTE-M modem firmware version 0.6.8-131.prealpha released which have a big advance.
Did the NB-IoT modem firmware which aligned to LTE-M 0.6.8-131 released?
Which...
Hi i am using ble_app_uart example in sdk 15.3.0 as far everything is fine even i added a app_timer for about 20 sec to advertise again but the problem is when i power up...
I'm trying to use the new ble_advertising_advdata_update from SDK 15.1 by doing
but I get NRF_ERROR_INVALID_ADDR
What do I need to do to get it to work?
Hello,
I use an nRF52840 that I program with Segger Embedded Studio. I am using J-Link driver version 6.44f.
When I want to connect to J-Link I get the following message...
Hi, all! After updating all libs can't flash. Have this error: Tested also with asset_tracker sample. Using runner: nrfjprog nrfjprog --ids Flashing file: /home/ilya/projects...
Hello Dear support,
Please help me with the error. I understand from the documentation that 0x11 err_code for nrf_drv_twi_tx() means invalid data. But I dont understand...
