Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Aim: transfer large data coming from UART to nRF52832 over BLE 5.0 as fast as possible. Want to use 921600 baud rate in the case given below.
Scenario:
SDK: 15.2.0 ...
Hello there!
I'm developing an application that uses BLE to access the flash memory of a nRF52832, using RTOS Zephyr 1.10.0. The OS is Ubuntu.
JLinkRTTClient gives me...
Dear Nordic,
I want to achieve long range in my custom board
I have some doubts:-
1. is it any difference in schematic for achieving?
2. Which HF crystal i used...
Hello, I was wondering how can I send data continuously over NUS.
I am using the ble app_uart and app_uart_c to program two NRF52382 with s132. My goal is to sample a signal...
Hi
SDK 15.2.0 ch_map[5] is 5 bytes long so 40 bits. Can you please confirm if ....
ch_map[0] bit 0 corresponds to channel 0
ch_map[0] bit 7 corresponds to channel 7...
the Product Specification v1.4 of the nRF52832 SoC. On page 23 the RAM0 block section 1 address is given as 0x21001000. From the context I believe, this should instead read...
Development Kit - nrf52 DK
SDK - 15.0.0
Computer Platform - Windows 7 - 64 Bit
My application was working fine until I decided to change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello everyone!
I have a question regarding where should I place NRF_DFU_SINGLE_BANK_APP_UPDATES flag. Should it be inside sdk_config.h in a bootloader or application? Or...
How to enable and disable FreeRTOS tickless idle(RTC or Systick)? Anyway to wakeup from tickless idle mode when there is BLE activities detected?
Setup:
1. nRF5_SDK_15...
Compiled Blinky client fails on Dongle PCA10059.
Precompiled version nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
I am trying to compare a bunch of BLE mesh options and I am trying to evaluate the software stack for nRF mesh
Whilst trying out the light switch proxy example, I noticed...
Hi Great Nordic Team:
I have some questions about nrf24ap2 reference schematic, please kindly help to give me some tips.
※it's reference circuit of Synchronous (bit...
Hi Sir,
As reference below link, and we can find the Tickless IDLE enabled ~700uA in SDK 15.2
https://devzone.nordicsemi.com/f/nordic-q-a/24733/nrf52840-sdk-14-0-0-and...
Hi again!
I'm trying to send/receive data between an nRF51(master) and a AVR/HM-11(serial/BLE module)(peripheral)
After following this visualgdb.com/.../ tutorial based...
Under some conditions I want to force advertising to transition from slow to fast. With SDK 14, I could just call ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST)...
