Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I use a Peer Manager in my project (nrf52832, SDK13.1).
Peer manager use FDS, but i also want to use FDS for storing user data.
As i know , FDS module use 1 virtural page...
Hi all,
I have here NRF51-DK, I am a bit familiar with the kit for a while.
Now I want to make a system using NRF518422 chip.
I manage to find a module - "Taiyo Yuden EYAGJNZXX...
I'm starting to read all the resources and examples included in the SDK. However, there doesn't seem to be a lot of emphasis on explaining how the programming architecture...
Hello,
I have the following observation regarding the potential problem with DFU bootloader
implementation :
I have noticed that the Bootloader DFU implementation (nRF5_SDK_13...
Hello!
I would like to program the nRF52 using the JLink Commander and protect it afterwards. Which register do I need to manipulate?
Thanks and kind regards,
Mi...
I download the nRF Toolbox app and its in swift.
My current app is in objective-C and I want to implement dfu in my app.
Is there any framework that can be used in my...
Hello,
I recently migrated to nrf52 and countering some problems
with NRF_ESB concurrently with BLE.
I started with This example which was a part of the Running micro...
The chip is nrf52832.
The SDK version that I am using is nRF5_SDK_13.1.0_7ca7556,the example that i used is ble_app_uart.
When i debug about low power,i encounter problems...
Hello,
I'm using NRF51-DK (PCA10028) and I want to be sure if I'm using the external 32KHz oscillator (X2).
I'm using SDK12.3.0. I'm running the beacon example.
In...
Hi,
Is there any tutorial already for the version 14.0.0 of the SDK (nRF52, more specifically I am using nRF52832)? I would like to know how to configure Advertising, and...
Hi
I have development kit nrf51 PCA 10028 and try to run uart example example with loopback (RX connected to TX, RTS connected to CTS). Unfortunately, after sending, I...
I'm using the bootloader_secure_ble example from SDK 13 on an nRF52832. I'm using the GCC toolchain. Here is an extract of the linker file from the example:
MEMORY
{
...
I'm running nRFgo Studio on Windows 10.
Have tried to re-install (nrfgostudio_win-32_1.21.0_installer.msi) without success..
Any idea what to do?
Thanks!
I'm using nrf52 with S132. I was trying ble_app_uart example and it is not printing any log messages into the COM. Do I need to do anything extra to make it work?
Hi there,
I am currently wondering if the following is possible?
As stated by the Cortex M4 reference manual states that a system can have 200+ seperate handlers within...
