Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Here Hung Bui (@hungbui) gave the good answer how to use bootloader with new S120 v.2.0.
I'm sorry, but can anybody check is I have a right settings on the Keil uVision...
Hi,
I need to send(using BLE) large amount of data's, which are collected by the accelerometer sensor for 1 hour. I have an external NOR flash where the accelerometer data...
While I am waiting for my hardware I wanted to test the control panel with my Xiaomi Mi Band.
But I only get a single horizontal line in the RSSI Graph..
As I read this...
Hi,
I would like to change device name more than 4 characters but I've found an exception of error code 12 (Data size exceeds limit) that return from initial of adverting...
Hi there
I started with an empty ble_template and added my own custom service emulating the batterey service, with all the same functions etc. Using master emulator i can...
I have a project in which I've started from the proximity app example code and added some UART stuff using app_uart.c. The linker is giving me this error immediately after...
Hi,
I'm trying to get an iOS app to connect to a Nordic BLE device. I'm a firmware guy with little app experience but I have gotten a app to work based off the code presented...
Hi,
Im new to BLE and still trying to wrap my head around things. I am using the both new nRF51 DK and nRF51 Dongle for testing at the moment. I know that the old dongle...
I would like to have track time of the day in my peripheral (s110)application. I understood that RTC0 is used by Soft device. RTC1 is used by app_timer application. I have...
hi nordic:
thank you for your great support!
question 1:
App: LightBlue in iOS.
when app scanning for perpherals ,i have found my device,show as "measurement…."
THEN...
Hi all,
I had a working TWI connection combined with BLE advertising. When
I added uart code for printing to putty this TWI connection was no longer functional.
So...
Hello,
I am currently working on a project and I would like to add some security to my device by preventing services from being discovered. Ideally when a user connects...
Hi
I am trying to use the internal ADC to capture an analog value every second. For this I use a timer to wake up every second, start the ADC and go back to sleep.
I...
Is anyone using the third-party BLE module from Taiyo Yuden? If so, where did you find the recommended footprint?
Taiyo Yuden's website only gives very limited information...
In the SDK 8.0 are only examples for nRF51422.
Is it possible to compile this for nRF51822 and is the softdevice 8.0.0 for both controllers?
Best regards,
Roman.
