I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello guys,
I'm trying to clearly understand the Bluetooth Peripheral Sample github.com/.../peripheral_uart and how it exactly works.. so i'm curious if there are some...
Hello, I would like to ask about the problem of how to implement SOC shutdown in NCS. 1. In V2.6.0, CONFIG_PM cannot be enabled, it will prompt that there are dependencies...
Hi there!
I was just trying an example of DFU over UART from the new nrf Connect SDK Intermediate course using the NRF9161DK but I'm unable to disable the mass storage device...
Dear sires,
Would it be possible to let you answer the following question?
In nRF5340 SDK, does it use CMD20"SPEED_CLASS_CONTROL " in SPI write sequence to ensure minimum...
During some operations like factory reset, or during a hardfault we want to check if the softdevice is enabled and disable it if it is enabled before continuing with further...
Hi,
I want to use BLE mesh to reach my application, the requirements below.
I have a root node and need to send the custom data to each client node and need to read...
Hello! I was building a custom board and tried to build the project for my board but it gives an error: === child image hci_ipc - CPUNET begin === loading initial cache file...
My understanding is that Singled-linked list built in to zephyr... https://docs.zephyrproject.org/latest/kernel/data_structures/slist.html But, I don't quite understand how...
Hey I've got this project that requires two buttons. In normal mode, these buttons react to the Ready pin switch signals. when it goes into sleep mode (where it controls other...
I am using ESB communication.
In general situations, data transmission works well. However, issues arise when multiple PTX devices transmit simultaneously.
It's understandable...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
hello,
I'm try to fit my application to Android 14.
my application implement nordic DFU library ( for nrf52833 running freeRTOS firmware SDK 16 ) version 2.5.0
while...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...
