Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi,
I'm using Zephyr controller instead of Nordic's Softdevice to use the DTM HCI feature in the Zephyr controller. Before switching to Zephyr controller, the application...
I want to be able to select the Network Coordinator Zigbee channel based on some GPIOs state (switches).
Is there any api function to set CONFIG_ZIGBEE_CHANNEL at runtime...
I am use sample "Bluetooth: Peripheral HR" as the base app
and added these settings to `prj.conf` on both central and peripheral sides
but I still got the...
Hello everyone, currently I am writing a program to read the SCD41(I2C) sensor and then use BLE to transmit information. With a separate program in twi_sensor, I see that...
Hello nRF team. Is there any different bewteen passing AT command and directly calling the Modem lbraries APIs(from nRF Connect SDK v2.5.2) to control the modem? For example...
Currently our product shipped with SD132 7.0.1, and bootloader/dfu compiled with SDK 16.0.0
We are testing update the bootloader on production devices, and want know how...
Hi Team, I am trying to do DTM test in NRF 52840 using Zephyr- os .The DTM code is working fine on my dev kit ( NRF 52832).I compiled DTM code for NRF 52840 and changed the...
Hi,
I have a problem with sending over NB-IoT to a cloud service. I have found that the helt of my messages only arrive in the AWS cloud and it seems like the modem also...
Hi Support Team
We use ncs to develop nRF52840 application and want to know how many low power mode do ncs have and how to enter these low power mode.We want the nRF52840...
Hello,
We are searching for a board that supports Angle of Arrival(AOA) and Angle of Departure (AOD) for conducted mode radio testing.We need a board euipped with an antenna...
Dear Nordic team
I have the following code for testing the SPIM function of nRF52832.
NRF_SPIM1->EVENTS_END = 0U; NRF_SPIM1->ENABLE = 0; NRF_SPIM1->ENABLE = (SPIM_ENABLE_ENABLE_Enabled...
Hi Nordic .
We are developing an application with nRF5340. In this application, we need to use the SPI Slave feature. According to the documentation, there isn't a clear...
Hi everybody I'm using sample bluetooth peripheral with sdk v2.6.1 and toolchain v2.6.1 to load with nrf5340 but it doesn't seem to build, I see the library has changed from...
Hi,
I am looking into adding BLE OTA firmware update functionality and started by exploring the example provided in Nordic SDK (SDK v16.0.0) while following the documentation...
i'm trying to get an interrupt using sensor lis2dw12 , i have connected my int1 pin of sensor to my gpio 0.10. whenever data is ready it should give me an interrupt this is...
