Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
My original project contains scheduler mechanism based on nRF5_SDK_17.0.2_d674dde\components\libraries\scheduler\app_scheduler.c. In ncs bare metal v2.0.1, I find the correspond...
So now I have the firmware revision mfw_nrf93m1_1.5.0, updated from 1.4.1 through FOTA. Meanwhile, I tried nRF Connect on nRF93M1 and I have some questions.
1. Most of cellular...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
Hi,
I have two questions regarding NB-IoT NTN support on the nRF9151 SMA DK:
Does the nRF9151 SMA DK support transmission of 1.25 kHz NPRACH with the currently available...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
On a Seeed XIAO nRF54LM20A (application core, nRF Connect SDK v3.4.0, Zephyr GRTC system timer, default LFXO), a minimal application with one 250 ms k_timer and a sleeping...
Device: nRF54L10 (nRF54L15-DK) SDK Version: nRF Connect SDK 3.0.0 Tool: SEGGER J-Flash
Issue Description:
We are using the ZMS (Zephyr Memory Storage) subsystem on the...
Have tried several times to install the SDK into VS code without success. This is one of the errors I am getting:
Failed to register SDK installation: west failed with...
Hello,
I am experiencing significant discrepancies when measuring current with a PPK2 in Ampere Meter mode using a Python API ( ppk2_api ) compared to the official Power...
Hello,
We run our Bluetooth Mesh product firmware in BabbleSim, on a simulated nRF52840 (nrf_hw_models, native simulator). We are on nRF Connect SDK v2.9.0. We would like...
Hello,
I am having an issue with nRF54LM20 rev B silicon where the gpio interrupts are not consistent for key functions with either code similar to the button demo or gpio...
Hello, i have unexpected disconnection on a nRF54L15 SoC. The goal is to synchronise 2 nRF devices : device 1 is a nRF54L15 SoC and ble nus central software, device 2 is a...
I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09.
#include <zephyr/kernel.h>
#include <hal/nrf_gpio.h>
...
Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
