Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Problem When attempting to flash a nRF board that uses pyocd as the runner (defined in devices’s baord.cmake) for flashing, the following error occurs.
It doesn’t matter...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
I'm developing a custom BLE sensor on an nRF52832 (E73-2G4M04S1B module, SoftDevice S132 7.2.0) with a companion Android app. On Xiaomi/HyperOS devices (confirmed on this...
Just purchased the PPK 2 Did the quickstart up and got this a message saying it's not yet supported. I am running Ubuntu Linux :
Distributor ID: Ubuntu Description: Ubuntu...
Your application for SUPL-C license has been denied.
Please make sure you have an active/approved DevZone account
You must apply using the same email address as for...
Hello,
I am using nrf5340 audio sample with the custom board. The nRF Connect SDK version I used is v3.4.0.
I added the following settings to prj.conf so that the custom...
Hi all,
the nRF54L15 hardware can support an external RF antenna switch. I don't see any hardware limitations (the switch could be controlled via GPIO), but the more interesting...
We are using the nRF9160 with firmware 1.3.6 to establish a DTLS connection to a server, using the Zephyr TLS stack.
The following problem occurs quite frequently: After...
Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
Hi,
In some cases, the UniqueID attribute of the Basic Information Cluster is empty (no value is set). CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_ONLY is enabled.
Environment...
Hi,
I'm working on a custom board based on Thingy:91 X PCA20065 rev 2.0.0.
I've kept the USB supply connection from the reference design:
nPM1300 VBUSOUT → R10 (2.2...
Hello,
I would like to use spi to connect to a ADC on a nrf54l15dk at high speed using DMA.
I want to use nrfconnect bare metal, but cannot find a starting example.
...
Hi,
we are building a backend that pulls device messages from nRF Cloud via the REST API instead of using the Message Routing Service. Before we finalize the polling logic...
Hello, Currently using nrf connect sdk version 3.0.0 and nRF5340, After some random time my device stop scanning coded phy beacon, it not coming in scan callback, I attached...
