I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
We have an application that needs to read device battery voltage and a sensor value every 10 seconds. The ADC is using burst mode and 8X oversampling to take each sample....
I created a new dts folder for nrf5340 appcore. The application works fine on the project, but I find netcore is not working properly. I found that the BOARD_ENABLE_CPUNET...
Hello,
My device is already implementing DFU over BLE and all is working fine. But now, I want to add the update over LTEM (Quectel BG77).
I want to proceed like this...
Basic OpenThread application built for 5340 crashes in net app.
The same application works fine on 21540 (52840 + 21540)
The crash seems to happen when some thread packet...
Hello,
I have 2x PCA10040 dev kits connected via SPI.
Device #1 is talking to a custom board MCU by UART
Device #2 is connected by BT to my android app
The task is...
Hello,
I am planning to use the balun BD2425P50100AHF with the nRF52833. The voltage on the pins BAL1 and BAL2 can go up to 15V.
I am wondering what is the maximum allowed...
Hi,
We have developed an application in central mode using BLE nRF52833 chip running on SoftDevice140 , Version 7.2.0
We now need to add support for FEM nRF21540 ...
Hi,
I am using NRF52840 development kit and I need to modify the PCNF0 register values for our application.
I am developing our application using the sample application...
I have ran the Mesh light demo successfully, and capture the Bluetooth HCI log (*cfa file) from my Android phone.
However，the transaction between my phone and the nRF52840...
Hi everyone,
Not very sure this is the right place to share this, if not, moderator please help me to move it to where it should be.
I just want to share with you a...
Hi, i have two nRF5340 DK that i'm testing with the Thread CoAP client/server samples.
I found out that with the newer DK, both the clinet and server samples work. With...
HI,
I keep working on my new customize board with nrf52833 SoC and now I want to add e-paper screen. There is any examples about adding a e-paper screen to customized board...
I am a beginner for ARM microcontroller, I am unable to generate the PWM wave and ADC simultaneously in the nRF51822, but both the things happening separately. I need the...
Hello,
I'm trying to understand if I can use BLE GATT Queue in my peripheral for sending Notifications. All the example and documentation about BLE GATT Queue seem to be...
Hi
When I build mesh bootloader code, there shows flash size not enough,
Could you tell me wher I can change the size, please?
c:/progra~2/gnutoo~1/62017-~1/bin/....
