I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi all ,
I had my code working on nRF connect 1.6.0 and now had to upgrade it to work with nRF connect 2.1.2.
I read the migration guide for nRF connect 1.x.x to 2.x.x...
I have tested sending NUS data from nRF52832 to laptop (Windows 10 + Intel core i5), but Windows app doesn’t received all NUS data. But When I tested sending NUS data from...
Hello,
I have downloaded the app for linux from here: https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop/Download?lang=en#infotabs
After downloading...
Hi,
I do have a question about the ble_app_uart for central device. Now it is set to make connection with the periheral based on the UUID. I can't find where in the software...
Hi,
I am writing a program that receives a command from a phone using the BLE UART example. The program can count up or down depending on the command. On every count, I...
Hi,
i'm developing an application that uses scan response.
AFAIK sd_ble_gap_tx_power_set is used to set the advertising tx power (BLE_GAP_TX_POWER_ROLE_ADV).
Is the...
Hello,
I am sunning trying to build the hello world sample as mentioned here:
For this project I am working on ubuntu(VM 22.04.1)
I have followed all the steps as mentioned...
-
Is it better as the ATT MTU size is larger?
I am trying to do nus communication between nrf board 1 and board 2. The data size I want to send is about 30 bytes. Previously...
To make sure that the nRF52840 SoC is not powered when the nRF power switch (SW8) is OFF.
So what happens if I power the nRF52840 SoC when the nRF switch (SW8) is ON ?
Hi ,
When i run samples/keys/hw_unique_key app and select nrf9160dk_nrf9160_ns board . The app can not run into main function instead run into system_halt.
__WEAK...
Please provide the part number(s) of low-cost NORDIC processors that have a quadrature decoder and a PWM.
We are working on an application that is using a Nordic nRF52840...
Hi,
During the validation of our device, we found that the RTC (synthesized from HFCLK) was quite a bit off. Instead of the expected 32.768kHz, we measured 33.047kHz.
...
Hi, I am using urf52832 ( also have 52833 dk).
I am trying to use another pin us uart, which tx is 29 rx is 30 define in project_pinconfig.h.
But I can't see any uart...
