Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Device: nRF52811
Board: custom (EYSNSNZWW module is used)
SDK: 16.0.0
SoftDevice: S112(v7.0.1)
Sample Project: ble_app_uart
I found that the current consumption...
Hi,
I have a product which will be available for Verizon, T-Mobile, and AT&T. I will have one firmware for all 3. Do I need to set anything special for any of these carriers...
I am in the process of migrating from PlatformIO on VScode to NCS on VScode, but im really struggling. I tried setting everything up on Windows and Fedora. on WIndows my main...
Hello Nordic Family. I hope this post finds you well.
I am working on a project where I have connected multiple sensors to the NRF52840. I have collected all the sensor...
Hi,
I have a quite controversial question I want to ask! I am new to the world of Nordic Semiconductor chipset and I need some information in order to decide which way to...
Hi I am trying to run the exampls of dwm1001 git file of ex_11b_leds on dwm1001 dev board using SES it gives me an error on Zephyr.h file , how can i connect to the nrf connect...
I developed a product for the customer with 9160. It used to run on the sdk of ncs1.2.0, and its fota function is normal; Now I have upgraded the sdk to ncs1.9.0, and found...
Hi!
Working on a BT peripheral device that will work in two modes depending on a runtime check at startup:
Sending data over BLE, running on battery (UART unused).
Sending...
Dear Support
I am developing a central application, scan and send out scanned packets via UART to host MCU, where I am thinking of calculate the advertising interval by...
Hi! I followed the recipe described on nRF Sniffer for Bluetooth LE to flash the sniffer .hex file into my dongle, install and configure the wireshard.
When I start the...
I am trying to install using VS code, using the video
https://www.google.com/search?q=install+nordic+visual+sydio+code&oq=install+nordic+visual+sydio+code+&aqs=chrome..69i57...
Hi everyone, i am new at this platform.
In my project, i need to take gps data from uart and send the data over zigbee with nrf52833. I haven't found any example and don...
Hi All, trying to find a cause of this problem, we have two devices, one is acting as peripheral and one as master.
Peripheral: ( nRF52832, s132 v7.0.1) a remote wireless...
I am trying to make a build with a slightly modified copy of the Zephyr button example on a nrf9160 board with a upgradable bootloader.
The following command can build our...
