Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
When I use 52832 to develop a mesh project and want to use uart to print information, I find that the code always reports an error because of the existence of printf. The...
Hello, while I was examining the BMD-380 datasheet, a section of which I shared the picture below caught my attention. What does factory image mean? I want to implement Bluetooth...
We are developing a product using the N52810 chip. We have J-link, and by downloading and connecting the Rf test tool,
the result is that there is no firmware. Can you support...
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
We are looking to use freeRTOS instead of zephyr on this board.
Finally with freeRTOS...
Dear Nordic support team
I tried to change the sample of ble_app_uart (nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040e) to support connecting 4 mobile...
I am working on an e-paper display with Bluefruit nRF52832 . I need to transfer a large image bitmap over Bluetooth Low Energy (BLE).
As BLE can send 255 bits at once, how...
Hi there,
We are using nrf9160 DK v1.0.0 ( pca10090 ). SES version 5.68 nrf Connect SDK 1.9.1 Windows 10
I want to make it as spi slave on pins CS=p0.10, mosi=p0.11, miso...
Hello Team,
We are developing an application with nRF52832 and ncsv1.8.0.
We are using NUS service to share data between Mobile and Nordic Chip. With the help of nRF...
Hey there!
The DFU over serial was successfully implemented. Unfortunately, I was only able to update the first node of my mesh, not all of them.
The first node in the...
Hello!
Recently I want to write a hci vs command in zephyr using nrf connect sdk, when I track ncs_v1.9.1\zephyr\samples\bluetooth\hci_pwr_ctrl samples code and find it...
Hi, for nRF5340 the "Build code" is a string of 3 chars
H - Hardware version code P - Production configuration code F - Firmware version code
https://infocenter.nordicsemi...
Hi
I am testing a thermometer peripheral using the nRF52840DK. It is advertising using BT LE Coded (BT_LE_ADV_OPT_CODED) with an advertising frequency of 3 seconds.
...
Dear Nordic Support Team,
I would like my nRF9160 DK to connect to multiple servers using TLS. Among others, I have read the following documentation: nRF9160: Simple MQTT...
