Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I have nRF5340 DK and nRF52840 DK and Flashed Central_hr_coded in nRF52840, Peripheral_hr_coded in nRF5340 DK. Followed the steps of Testing as showed in below link...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
Hi.
In a prototype built for a small group of test users (20-25), we want to implement a simple tactile reset button for use in case of an anomaly (as the prototype software...
Hello,
I am using nRF9160 dev kit in Chicago (USA) and in Aldingen (Germany) where I am using same firmware for both DK to get GPS Fixes for location. But surprisingly in...
good try,
i tried adding buttonless dfu service to ble hid_mouse/keyboard sample in nRF52 SDK 17.1 with PCA10040 dev board but it does not show up in the list of devices...
If the privacy feature is disabled, calling bt_conn_le_create will change the state to BT_CONN_CONNECTING_SCAN (since bt_dev.le.rl_size == 0) and then call bt_le_scan_update...
Hello,
I have been working with Adafruit Feather nRF52 Bluefruit LE for my project, I have two of these modules.
Recently, while I uploaded code into it and push the reset...
Dear Forum,
I am using the provided BLE-NUS UART examples (central/peripheral) to create a COM link via bluetooth.
As I failed to generate a setup which directly operates...
I am using SDK_17.1.0_ddde560 and IAR compiler for the project. We want to create a makefile based compilation for IAR.
Are there any examples wherein makefile is used with...
Hi,
I am looking at this page for nRF25832 https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.1.0/lib_bootloader.html
and I notice that the Application area (incl...
