I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I'm working through the QDEC using the nRF2840 evaluation board and I've run into some confusion.
I have trouble getting the ACC or ACCREAD registers to actually...
We received the nRF9160DK that included default firmware for the Asset Tracker v2. The default version appears to be an older version of the application.
We built the latest...
So... I hate being that guy who says, "I didn't touch anything!". So, clearly I broke something. But I can't say I can think of what it was. I went to create a new application...
I am trying to upgrade from nRF Connect SDK v1.6.1, running under Ubuntu 18.04 using the Nordic Edition of SEGGER Embedded Studio as the Integrated Development Environment...
Hi, this is my setup:
nRF52840 Dongle configured to run as a peripheral BAS.
The BLE desktop app was used to configure the dongle.
I know that the dongle is working...
I was wondering how one might get the nRF9160 to enter the low power modes when making my own firmware? If possible could someone point me in the direction of an implementation...
We are building a gadget which senses temperature and humidity level using nrf5340 and using i2c as interface. We are using a slave which has SHT3X sensor for reading the...
I've been trying to use the NVS subsystem along with BLE and FOTA.
I got BLE and NVS working fine.
But if I enable FOTA (just including the code, not running an update...
I'm having trouble with a computer that can't run a Python script, which is using the library pc_ble_driver_py
I'm confused about the answer posted in
I've tried downloading...
Hi!
For a custom project, I need to enable and disable soft device for power consumption optimization. I've followed ble_app_gzll to enable and disable soft device. Unfortunately...
Hello,
I'm using the nRF52840 DK, SDK 17.1.0 and SoftDevice S140. My project is based on the Blinky peripheral example. The problem is the following:
Basically, turning...
I see a lot of threads about how you need to disable the UART while you're not using it because it has a couple of milliamps power consumption.
However, most of those threads...
Hello Team,
We are in process of designing our product with nRF52833. To secure our product and possible Firmware readouts, we are planning to use the APPROTECT feature...
So, I'm working on a project with two RGB LEDs, that's going to be powered by a coin cell. The device is going to spend most of it's time asleep, only waking up for a minute...
