Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I have been evaluating the nRF5340dk for our application purposes and I am currently investigating on how the bluetooth directional finding works.
I happened to...
Hello Devzone Community,
I am continuing my long trek toward single-microamp operation of an nRF9160 based, custom board. On the LTE modem front I am making `AT+CPSMS=`...
Good afternoon.
We have an issue which we'd like to prevent, but suspect it may entail changing the out-of-the-box MCU Boot / SMP BLE code / process.
If we flash our...
Hello, I developed a custom PCB that uses the nRF52810 microchip, and I wrote a firmware that needs to use three RTCs.
The program is supposed to wake up the CPU by an RTC...
Hi there, i have a thingy91 for the electromaker contest. I've flashed the nrf51 bridge firmware using MCUboot. All went well. However, when i try to put in DFU mode the nrf9160...
Rookie question.
Finally I put my ble working passing a number thanks to the support from this forum. But now my problem is how to send a string with around 100 characters...
Hello nordic team, Question 1 How can I customize the Asset Tracker v1 to send Asset Orientation "FLIP" in the same frequency as the temperature and the rest of the values...
When communication fails on NRF connectivity dongle (In Python via pc_ble_driver) and Error code: NRF_ERROR_BUSY is received on attempts to write and one restarts python script...
Hi,
I am following below link for DFU over BLE. Link ( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu ) currently it is working fine...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
I'm running into an odd problem with the PWM driver. We're using SDK 17.0.2 and the S113 softdevice on an nRF52833. We're using the PWM module to drive some LEDs.
The nRF52833...
1. nRF Connect SDK v1.9.1
2. Segger 5.68
3. sample name : multiple_adv_sets
I am developing through multiple_adv_sets.
I want to test by changing the uuid in uuid...
Hello
I have installed NRF Connect for Desktop in my system (64bit, i3 CPU). I want to debug my custom hardware using the nRF9160 Development Kit. I have connected the nRF9160...
We have a big application bigger than 500ko and we need a littlefs partition, so we end up with a mcuboot_secondary smaller than the mcuboot_primary (actually we put it to...
