We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi Community,
Recently I have started testing my BLE peripheral running HRS with iPhone. My device is running SDK16 on nRF52 SoC. This is working perfectly with Android...
Can I use this aerial: https://thepihut.com/products/pycom-lte-m-cellular-antenna with the Thingy91 LTE-M interface. I am unsure whether the Thingy91 has a uFL connector as...
We are developing part of an application for products that are supposed to have 10+ years of service life with updates over the whole lifetime. We want to have a flash memory...
The PS for the nRF52840 indicates that the current consumption when the radio is transmitting BLE at 1Mbps is 16.4mA (p61). There is no mention of current consumption at 2...
Hello, I'd like to check what is the typical distance using 0 dBm tx power using Nrf52840?
I am using this BLE module based on Nordic, and it seems to work ONLY 2-3m far...
Hello
I am getting started with Nordic devices.
I recently bought a Thingy:91 and followed a tutorial to load the Asset Tracker application on to the device – this...
Dear,
We have been using QSPI external flash (MX25R64 installed at nrf5340 DK board) to write data. Particularly, when we ran flash_area_erase function ( located at zephyr...
Hello All,
How can I get my nRF52840's MAC address in Zephyr? Actually, I want to append the last 4 characters of the MAC address in CONFIG_BT_DEVICE_NAME.
So, when I...
Hello, we are developing a zephyr application on top of nrf52 soc. We can use the built-in zephyr drivers for most modules (ex: I2C, UART, nvm, etc.); however, for some modules...
I am really new at working with Bluetooth and the various protocols contained within.
I am using SDK 17.0 and drivers 2.7. I am working on a DK-52 board.
I am working...
The TWIM peripheral allows you to tx multiple buffers back-to-back like this:
- Set buffer 1 in TXD.PTR, TXD.AMOUNT - Trigger TASKS_STARTTX - Wait for EVENTS_TXSTARTED ...
Hi,
For testing purposes, I need a copy of the spec that the Nordic UART BLE service adheres to. Ex. minimum capabilities, mandatory functionality and attributes, etc. ...
Hello,
I tried enabling the Zigbee shell, through RTT, in my application and when that failed I built and burned the nrf/samples/zigbee instead, slightly modded to get rid...
Hi All. My task is simple. I want to implement LE secure connections on DFU. I have seen the ble_gls example. It has a passkey for bonding, I am looking into that too. I ran...
