I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
we have a 'long lived' tcp connection w/ regular data sends (1hz of 256 bytes for mqtt publishes) where sendmsg() sometimes returns EAGAIN. when trying again it usually works...
Hi Nordic team,
I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host.
My application has multiple BLE connections...
Hi,
I am developing on the nRF5340 and using an external modem and an external GNSS module. I am using SDK version 3.4.0.
To operate the modem, I use `modem_cellular...
Hello, We have some problem with connection to WIFI AP.
On NCS v3.4.0, once our device has associated with a WPA3-Personal AP, it can no longer
associate with a WPA2...
I am designing a board around the nRF52832 (QFN48). According to Table 5 in the product spec, GPIOs P0.22–P0.31 are marked "Low drive, low frequency I/O only" (see §4.3.1...
Hello,
Is modem fw `mfw_nrf9151-ntn_1.0.1` production-ready? Is it safe to have our manufacturer flash that instead of the `mfw_nrf91x1_2.0.4`. We are using the ncs-serial...
I'm trying to understand the npm1300-CAAA V1.1 example for configuration 1. The layout looks like this:
You can easily see that several pins are connected on the right...
According to the nRF52840 Product Specification, I observe only the typical value is specified below ：
ION_RAMON_RTC (System ON, full 256 kB RAM retention, wake on RTC...
Hi nordic
I am using the nRF54L10 and Nordic Zigbee Add-on version 1.3.0
I have probably been raising questions about polling for quite some time,
but I have not...
SUMMARY
A custom board (nRF52832, BLE Central + Peripheral roles simultaneously) reliably hits a hardware watchdog reset (RESETREAS shows WATCHDOG only, never CPU_LOCKUP...
Hello,
I have added DFU capabilities to my NRF54L15 project using:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
and
SB_CONFIG_PARTITION_MANAGER =y
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
